SSA Enhanced Adapter Front   FRU 89H5667 / FC 6216

I noticed that the Microchannel SSA adapters all use the same PCB. Dan Kalish, mouthpiece for the Microchannel Mafia, sent me a 4-G so I could get it right.

U6 / U15 31H8637 BIOS Odd / 31H8636 BIOS Even. The 4-G uses the same P/N BIOS as the 4-I. This makes me hopefull that a common ADF and drivers can be used for all MCA SSA adapters..

J2, J6
   The adapter card has 2 internal SSA connectors and 4 external connectors. This allows one of the 2 dual-port SSA nodes to be connected either internally or externally to the system unit. The internal connectors are 2 x 3 pin SSA connectors.
    Ports B1 and B2 have both internal and external connectors. The marking also indicates that ports A1 and A2 are paired, that is, they are connected to the same SSA loop interface chip.  Similarly, ports B1 and B2 are paired.

+5 V power is available on the connector to power an external optical extender.

Interior SSA Port Pinouts
   Thanks to David Ress for finding this after I lost the reference... Pin 1 is marked on the outside of the header on the PCB.

  1  Line Out +  6  Line Out -
  2  Ground      5  Ground
  3  Line In -   4  Line In +

J14 Exploration
   Dave Ress tips back his miner's helmet and says:
   I checked the SSA adapter I have, and it has the solder pads for a 6-pin port, but that is all. Looking at the A side and numbering the solder pads from left to right, I find:

Pad 1 - GND
Pad 2 - Pin 5 of U7
Pad 3 - Pin 4 of U7
Pad 4 - Pin 3 of U7
Pad 5 - Pin 6 of U7
Pad 6 - +5 V

Looking at: SCC2691AC1A28 we learn that U7 is a UART, so the PS/2 port is really a serial port as the pins of U7 are mapped as:

Pin 3 - RxD
Pin 4 - TxD
Pin 5 - MPO => multi-purpose output (clock pulse?)
Pin 6 - MPI => multi-purpose input (clock pulse?)

Beyond that, I have no idea where the U7 chip interfaces to. I tried to map D0-7, but no luck there.

SSA Mini-Ports
   SSA connectors are 9-pin high-density shielded ITT-Canon Micro MDSM connectors
  Pin   Assignment    Pin  Assignment
   1     Ground        6   Line Out +
   2     Line Out -    7   No connection
   3     Ground        8   +5 V
   4     Line In -     9   Line In +
   5     Ground

SSA Drive Connectors
  David Ress started diddling and said:
I took one of my SSA drives carriers apart this morning. It originally went into a 7133.

I did this for two reasons: first, I have always wondered how to connect an internal SSA drive up to the B1 and B2 internal connectors.  Second, if the SSA adapter has just a six pin ribbon connector, I was curious what the physical connector looked like on the SSA drive.

In looking at the SSA drive carrier, the first thought was "what in the world?", as the SSA drive carrier has a EURO 72-Pin style connector (think mini-Nubus).  72 pin connector to support a 6 pin ribbon connector?  But, as it turns out, 32 of the pins are no-connect.

Further disassembling the SSA drive carrier revealed a IBM DFHC 4.5GB drive, made in 1996.  Note: the SSA drive carrier has a label that says assembled on 23 Feb 2000, I guess IBM had many units left over.

In removing the DFHC I learned that the connector is very unusual, unlike anything I have seen before. I guess I was hoping to see a SCSI-2 connector as SSA is a superset of the SCSI-2 protocol, but that was very much wishful thinking on my part.

SSA Unitized Connector
SSA Unitized Connector 

SSA Port on Unitized Connector

Option Port on Unitized Connector

Power Port on Unitized Connector

Carrier connector
    4 x 32 female contact, BERG HPC connector, part number 99F9429. Ed. There seems to be different models with different carrier interfaces. YMMV.

Fibre-Optic Extender
   A fibre-optic extender is available to connect an industry-standard fiber optic cable within an SSA loop when that loop is used with a 7133 SSA Disk Subsystem. With a fibre-optic extender attached at each node, the distance between them can be up to 2.4 km. The maximum sustainable data-transfer rate in a single direction  on an SSA link is approximately 18 MB/s. Extending the link with a fiber optic cable results in no degradation of  this data-transfer rate for lengths up to 200 meters, and a gradual reduction in the achievable data-transfer rate beyond this distance. This data-transfer rate reduction generally has no effect on SSA subsystem performance for most applications.

Light Pipes on D4 and D5
   Both LEDs are normal LEDs on the PCB. There are light pipes to transmit the light to the outside.

Each pair of connectors has a green light that indicates the operational status of its related loop:
 

Status of Light	Meaning
Off	Both SSA connectors are inactive. If disk drives or other SSA adapters are connected to these connectors, either those disk drives or adapters are failing, or their SSA links are not active.
Solid	Both SSA links are active (normal operating condition)
Slow Flash	One port of a SSA loop interface is not operational

SSA Enhanced Adapter Back

 

 40 MHz version of the ARM6 Application-Specific Standard Product (ASSP) version of the new ARM processor, designed the VY86C06040, is pin-to-pin compatible with lower clock frequency versions.  It operates with a 40 MHz clock and exhibits a peak performance of 40 MIPS and a sustainable performance of 26 MIPS at 5