AC ADAPTER: 
   The AC adapter is an AC to DC converter which supplies the necessary power to the computer. The AC adapter also charges the battery pack when it is installed in the computer.
 o   Input rating:  100-240 V AC, 2.0A, 50/60Hz
o   Output rating:
    -   +20 V DC 2.0 A
    -   +20 V DC 2.5 A (Expansion Cartridge attachment)
    -   Battery Pack:  10.8 V DC, 1450mAH/cell, 18 cell/pack
o   Operating temperature 5 -- 35 (degs) C (41 -- 95 (degs) F).

NIMH BATTERY PACK:

 
 

The two fusible links are Klixon 4-S F5J 4MM75A

The central item is a PTC resistor (I think)
 
 
 
 
 
 
 

o   PC Cards that do not support the power management function may cause  the shorter battery operation hours.

FUNCTION                             MONOCHROME          COLOR
Power off/Suspend charging           1.4 hours           1.4 hours
Charging during operation            1.5 hours           1.5 hours
Quick charging                       1.4 hours           1.4 hours
Suspend Life (Full) (*)              48  hours           36  hours
Suspend Life (Partial) (*)           6.0 hours           6.0 hours
Battery Operation Hours (**)         4.0 - 8.0 hours     2.4 - 4.8 hours

 (*) Full battery.
 (**) Power management and application dependent.
       The ThinkPad 700 and 720C systems also support a suspend/resume function when the PCMCIA card is installed.  For example, when you are operating with the communication application with PCMCIA cards, after suspend/resume you do not need to restart the operating system and communication application.

NIMH BATTERY PACK WITH POWER STATUS INDICATORS: 
   This has five power status LED indicators and one push button located on the front bezel of a battery pack.  These LEDs show how much battery power remains when the button is pushed.  In full-charged state, all five LEDs are lit.  One LED means about 20% of battery power.  The battery operation hours and charging times are the same as the standard NiMH battery pack.

QUICK CHARGER: 
  The quick charger has two slots to charge two battery packs simultaneously.  Charging begins on the first battery pack installed, then after it is completely charged, the other installed battery pack is charged.  A REFRESH BUTTON is provided for each battery pack slot to DISCHARGE the battery packs before charging them.  There are identifiers and indicators that tell the charging
status for each battery pack installed.

Power Systems Checkout
Note:  One or all of the batteries can discharge if there is a short circuit in the system.
1. Replace the failing FRU if the power supply problem is caused by a short circuit.
2. Determine if one (or all) of the batteries have become discharged. Replace any discharged battery with its spare, if available.

How to test:
AC Adapter
Car Battery Adapter (700 only)
Battery Pack
Backup Battery
Standby Battery
Quick Charger
Voltage Converter (700, 700C)
Voltage Converter (720, 720C)

1. If any noise can be heard from AC adapter when it is plugged into ac power outlet, replace AC adapter. If no noise can be heard from AC adapter, go to step 3.
2. If a noise is still heard from new AC adapter, suspect the computer. Replace AC adapter with the original one, then go to the next step. If no noise is heard from new AC adapter, the original AC adapter is defective.
3. Unplug the AC adapter cable from the computer and measure the output voltage at the plug of the AC adapter cable.

   ^o  If the voltage is not correct, go to the next step.
4. Unplug AC adapter cable from ac power outlet and wait for a few minutes.
5. Plug AC adapter cable into ac power outlet.
6. Measure output voltage of AC adapter. 
     If the voltage is still not correct, replace the AC adapter.
     If voltage is correct, plug AC adapter cable into computer and try the failing operation again.
     If the problem goes away, suspect the continuity or installation of the AC adapter cable.
     If the problem is not corrected, replace the voltage converter.

1. Unplug the car battery adapter cable from the connector, if connected.
2. Plug the car battery adapter into the cigarette lighter socket. Note:  If the adapter is already plugged in, be sure to unplug the adapter from the cigarette lighter socket, then plug it back in.
3. Measure the output voltage of the car battery adapter cable. 

   ^o If the voltage is correct and the power-on indicator on the car battery adapter is on all the
time, the car battery is working correctly. Replace the voltage converter. If the problem is
not resolved when the voltage converter is replaced, go to Checking the Voltage Converter
(700, 700C) or “Checking the Voltage Converter (720, 720C)” 
   ^o If the voltage is outside the normal voltage range, do one of the following:
     – Try the above test procedures using a different car, if one is available.
     – Replace car battery adapter if computer works with AC adapter but not car battery adapter.
Note:  If output voltage from cigarette lighter socket of car is less than 10.5 V dc, the car battery adapter's power-on indicator blinks and a continuous noise is heard. Service the car battery .

The  IBM  Car  Battery  Adapter  can be used on the ThinkPad 720C:
    -   Charge the battery whih system unit turned off
    -   Use system with battery removed before plugging  in car adapter and turning system on.

NIMH BATTERY PACK WITH POWER STATUS INDICATORS:  A rechargeable battery pack with five power status LED indicators and one push button located on the front bezel of a battery pack.  These five LEDs show how much the battery power remains when the user is pushing the button.  In full-charged state, all five LEDs are lit.  One LED means about 20% of battery power.  The battery operation hours and charging times are the same as those of the standard NiMH battery pack.

1. Carefully place the computer bottom-side up.
2. Remove battery pack and measure voltage between battery terminals 1 (+) and 3 (N).

   ^o If voltage is less than +10.0 V dc, the battery pack has been discharged or is defective.
   ^o If the voltage is more than +10.0 V dc, go to the next step.
3. Using an ohm meter, measure the resistance between battery terminals 2 (T) and 3 (N). The
resistance must be 4 to 30 kilohms.
   ^o If the resistance is not correct, replace the battery pack.
   ^o If the resistance is correct, go to the next step.
4. Install battery pack and plug AC adapter cable into computer to charge battery pack.
   ^o  If the battery power status indicator is blinking (orange) and battery charging indicator is on,
replace the battery pack. If the battery is charging normally, the battery is OK.

 
 
 
 

Wire	Voltage (V dc)
Red	+2.5 to +3.7
Black	Ground

   ^o If voltage is correct, replace system board.
   ^o If voltage is not correct, backup battery was discharged by a short circuit or it is defective.

  The backup battery is a CR2032 with solder tabs. The battery is covered with clear heat shrink tubing. The battery is not sealed airtight as the ends are open (not much).

 
 
 

Pin	Voltage (V dc)
1	+4
2	Ground

   ^o If the voltage is less than +4 V dc, replace the voltage converter.
   ^o If the voltage is more than +4 V dc, go to the next step.
 

7. Power-off the computer and unplug the AC adapter cable from the computer.
8. Reconnect the standby battery to the voltage converter.
9. Plug AC adapter cable into computer and power-on computer. Allow 30 min for standby battery to charge.
10. Power-off computer and unplug AC adapter cable from computer - remove standby battery.
11. Measure the voltage of standby battery.
   ^o If the voltage is less than 3.5 V dc, replace standby battery.

   If a humming or buzzing sound is heard from the quick charger when it is operating, replace the quick charger. If the charger is operating at a normal quiet sound level, do the following.

1. Perform steps 1 - 3 of  Checking the Battery Pack to ensure correct battery pack operation.
2. Connect power cord to quick charger and ac power outlet. Ensure power-on indicator is on.
   ^o If power-on indicator does not turn on, check quick charger's power cord for correct continuity and installation.
   ^o If the problem is not corrected, replace the quick charger or the power cord.
3. Install the battery pack into the quick charger.
   ^o If the charging indicator does not start blinking, replace the quick charger.

QUICK CHARGER:  The quick charger has two slots to charge two battery packs simultaneously.  Charging begins on the first battery pack installed, then after it is completely charged, the other installed battery pack is charged.  A REFRESH BUTTON is provided for each battery pack slot to DISCHARGE the battery packs before charging them.  There are identifiers and indicators that tell the charging status for each battery pack installed.

Signal	V dc Min.	V dc Max.
VA	+4.75	+5.25
VG	+4.75	+5.25
VB	+4.75	+5.25
VC	+3.42	+3.78
PWRGOOD	+4.00	+5.25

Note:  Only VOLT is marked on the system board.
Use the above figure to locate the VA, VG, VB, VC, and PWRGOOD signal names.
   ^o If all voltages are correct, the voltage converter is operating correctly.
   ^o If the voltages are not correct, go to the next step.
 

8. Power-off the computer and unplug the AC adapter cable from the computer.
9. Check for a short circuit between GND and VA, VG, VB, or VC.
   ^o If there is a short circuit, replace the following FRUs one at a time to correct the problem.
      – Voltage converter
      – System board
  ^o If there is no short circuit, go to the next step.
10. Check the output voltage of the AC adapter cable (see Checking the AC Adapter).
   ^o If the output voltage is correct, go to the next step.
11. Replace the following FRUs one at a time.
    – Voltage converter
    – System board

   ^o If any voltage is not correct, go to step 9.
   ^o If all voltages are correct, the voltage converter is operating correctly. If the power problem did not reoccur, reconnect the devices removed in step 2 to isolate a device problem.
   ^o If all the voltages are correct and the power problem still exists, replace the following FRUs
one by one.
  – System board
  – Processor card
9. Power-off the computer and unplug the AC adapter cable from the computer.
10. Check for a short circuit between Ground and VA, VG, VB, VA3 or VB3. The following table shows which FRUs can cause a short at each signal.
   ^o If there is a short circuit (less than 10 ohms), remove the FRUs indicated one at a time until
the short circuit disappears. Replace the FRU causing the short circuit.

FRU	VA	VG	VB	VA3	VB3
Voltage converter	x	x	x	x
Processor card			x		x
System board	x	x	x	x	x
Video card	x		x	x	x
Base memory card	x
Keyboard control card	x		x
Math coprocessor			x		x
Diskette drive			x
Hard disk drive			x
LCD	x
Indicator assembly		x	x

11. If there is no short circuit, replace the following FRUs one at a time.
  ^o Voltage converter
  ^o System board