Radius MultiView 24
@8066.adf Radius Multiview
24 (NOT SVGA
Multiview!)
MV24DISK.ZIP
Multiview
24 installation disk
Radius_MV24 My archive...
WD95C00-SET1 Datasheet
Bt473 Datasheet
MT42C8255DJ
-8 Datasheet
Multiview 24
ADF Sections
Radius
MultiView 24
P1 Solder
pads for 100 pin header
P2 Solder pads
for 44 pin header
P4 25 pin
video pass through
U8 WDC
WD95C00-MR
U9-U20 256Kx4
DRAM MT42C8255DJ
-8 |
U24
Brooktree Bt473KPJ80 RAMDAC
U28 PLCC
U32
Altera
U35-U37 WDC
WD95C01-LR
X1 14.3181 MHz
Crystal |
Win95 and NT
The MultiView 24 board
will not
be updated beyond this driver version, nor will it be
supported under Windows
95 or Windows NT. Windows 95 expects a
user-accessible base MMIO
address, and since the MultiView 24 board pre-dates
these requirements
by several years and offers no MMIO interface, it will
not be possible
to retrofit or upgrade it to run under Windows 95.
MV24SET.EXE
MV24SET.EXE is the setup program for the
MultiView 24.
It must be run in order to enable the ROM and select its
address, and to
select a monitor type and appropriate refresh rates.
MV24SET will
be run automatically the first time INSTALL is run on a
new MultiView 24.
If you wish to change your ROM address or monitor type or
refresh rate
after the first time installation to your hard disk, run
MV24set.exe
MV24INIT.EXE
MV24INIT.EXE is an optional substitute for
the on-board
ROM. It performs the same initialization as the
ROM does on power-up.
This program should only be installed if MV24SET has
been run and it has
been determined that the on-board ROM must be disabled
due to unresolveable
address conflicts. If MV24INIT is used to replace the
ROM, it must be run
every time the system is booted, preferably as part of
the AUTOEXEC.BAT.
The INSTALL utility will automatically add MV24INIT to
your AUTOEXEC.BAT
file if you so choose. To install MV24INIT, run
INSTALL from the
Utilities and Drivers disk, select MV24INIT, and
complete the installation
according to the on-screen instructions.
CLR24.EXE
CLR24.EXE is a screen clearing utility for
the MultiView
24 when it is used in a dual-screen configuration (VGA
and MultiView 24
connected to separate monitors). If an application
leaves a graphics
image on the MultiView 24 screen after exiting,
CLR24.EXE can be run to
clear the image from the MultiView 24 screen. To
run this utility after installation
to your hard disk, run CLR24.exe
FPP1024.EXE
FPP1024.EXE is a utility for 1024x768 modes
when the MultiView
24 is connected to a Radius Full Page Pivot display.
AdapterId
8066 Radius
MultiView 24 MC
Card Enable
This allows you to disable the Radius
MultiView 24 card.
<Enabled>,
Disabled
EPROM Enable
This allows you to disable the EPROM of the
card.
This is useful only if other adapters conflict with the
MultiView 24."
<Enabled>,
Disabled"
Note that if you have disabled the ROM, you must
run MV24INIT.EXE,
which is the RAM replacement for the ROM, every time you
boot your system.
9595 Main
Page
|