|
| Interrups | Categories | Contents |
AX = B10Ah subfn 8086h BH = bus number BL = device/function number (bits 7-3 device, bits 2-0 function) DI = register number (0000h-00FFh) (see #00878)
Return:
CF clear if successful ECX = dword read CF set on error AH = status (00h,87h) (see #00729) EAX, EBX, ECX, and EDX may be modified all other flags (except IF) may be modified
Notes: This function may require up to 1024 byte of stack; it will not enable interrupts if they were disabled before making the call. The meanings of BL and BH on entry were exchanged between the initial drafts of the specification and final implementation
See Also: AX=B10Ah - AX=B10Ah/SF=1106h - AX=B10Dh
Format of PCI Configuration data for Intel 82375 EISA Bridge: Offset Size Description (Table 01054) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 0482h)
(revision numbers:
03h = 82375EB, 04h = 82375SB) 40h BYTE PCI Control !!!intel\29047704.pdf pg. 32 41h BYTE PCI Arbiter Control 42h BYTE PCI Arbiter Priority Control 43h BYTE PCI Arbiter Priority Control Extension 44h BYTE MEMCS# Control 45h BYTE MEMCS# Bottom of Hole 46h BYTE MEMCS# Top of Hole 47h BYTE MEMCS# Top of Memory 48h WORD EISA Address Decode Control 1 4Ah 2 BYTEs reserved 4Ch BYTE ISA I/O Recovery Time Control 4Dh 7 BYTEs reserved 54h BYTE MEMCS# Attribute Register #1 55h BYTE MEMCS# Attribute Register #2 56h BYTE MEMCS# Attribute Register #3 57h BYTE reserved 58h BYTE PCI Decode Control 59h BYTE reserved 5Ah BYTE EISA Address Decode Control 2 5Bh BYTE reserved 5Ch BYTE EISA-to-PCI Memory Region Attributes 5Dh 3 BYTEs reserved 60h 4 DWORDs EISA-to-PCI Memory Region Address registers 1-4 70h 4 DWORDs EISA-to-PCI I/O Region Address registers 1-4 80h WORD BIOS Timer base address 82h 2 BYTEs reserved 84h BYTE EISA Latency Timer Control Register 85h 3 BYTEs reserved 88h DWORD PCEB Test Control Register ("DO NOT WRITE") 8Ch 116 BYTEs reserved
See Also: #00878 - #01055
Format of PCI Configuration data for Intel 82434LX/NX Cache/DRAM Controller: Offset Size Description (Table 01055) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 04A3h)
(revision numbers:
01h/03h are 82434LX, 1xh are 82434NX) (command register only supports bits 8,6,2,1,0) 40h 16 BYTEs unused (hard-wired to 00h) 44h BYTE ??? (AMI BIOS writes 00h) 45h BYTE ??? (AMI BIOS writes 00h) 50h BYTE Host CPU Selection (see #01056) 51h BYTE deturbo frequency control register when deturbo mode is selected (see PORT 0CF9h), the chipset places a hold on the memory bus for a fraction of the time inversely proportional to the value in this register by comparing it against a free-running 8-bit counter counting at 1/8 the CPU clock speed (i.e. C0h = 1/4, 80h = 1/2, 40h = 3/4, 20h = 7/8, etc.) (only bits 7-6 writable, bits 5-0 hardwired to 0) 52h BYTE Secondary Cache Control (see #01057) 53h BYTE Host Read/Write Buffer Control (see #01058) 54h BYTE PCI Read/Write Buffer Controlbits 7-3:
Reservedbit 2:
LBXs connected to TRDY#bit 1:
Enable PCI burst writesbit 0:
Enable PCI-to-memory posted writes 55h 2 BYTEs reserved 57h BYTE DRAM Control (see #01059) 58h BYTE DRAM Timing (see also #01117)bits 7-2:
Reservedbit 1:
(NX only) RAS# Wait Statebit 0:
CAS# Wait State (one extra wait state before CAS# within burst cycle) 59h 7 BYTEs Programmable Attribute Map registers 0-6 (see #01118) 60h 8 BYTEs DRAM Row Boundary registers 0-7 (chip revisions numbered < 10h [LX] only support six rows of DRAM) each register N indicates the amount of cumulative amount of memory in SIMM banks 0-N, in multiples of 1M; offset 67h (65h on 82434LX's) contains the total amount of memory installed in the system; on the 82434NX, two additional bits are concatenated to each row boundary from the DRAM Row Boundary Extension registers to allow up to 1024M of memory to be specified (though only 512M are supported) 68h 4 BYTEs (NX only) DRAM Row Boundary Extension registers each nybble is concatenated with the corresponding DRAM Row Boundary register to form a 12-bit boundary value (of which only the low 10 bits are actually used) 6Ch DWORD reserved (hardwired to 00000000h) 70h BYTE Error Command (see #01060) 71h BYTE Error Status (see #01061) 72h BYTE System Management RAM control (see also #01123)bits 7-6:
Reservedbit 5:
Map SMM-mode memory (64K) into address space when bits 2-0 = 010 (default 3000h:0000h; can be changed by first SMM event)bit 4:
Close SMRAM space (allows data accesses to be forwarded to PCI bus while execuding SMM code)bit 3:
Lock SMRAM space (can't be cleared by software)bits 2-0:
SMRAM memory address (010 = Axxxxh, 011 = Bxxxxh) 73h 5 BYTEs reserved 78h WORD Memory Space Gapbit 15:
Enable ISA holebits 14-12:
Size of ISA hole in MB (less 1); must be power of 2bits 11-8:
Reservedbits 7-4:
Bottom of ISA memory hole in MB (must be multiple of gap size)bits 3-0:
Reserved 7Ah 2 BYTEs reserved 7Ch DWORD Frame Buffer Range (see #01062) 80h 128 BYTEs reserved
Note: The 82434NX is part of the Intel Neptune chipset
See Also: #01064 - #01083
Bitfields for Intel 82434LX/NX Host CPU Selection: Bit(s) Description (Table 01056) 7-5 host CPU type.
LX:
Hardwired to 100 (Pentium).NX:
"reserved" (101 on RB's system) 4-3 reserved 2 enable L1 cache 1-0 Host Operating Frequency (set according to external bus speed).00:
Reserved.01:
50 MHz.10:
60 MHz.11:
66 MHz.(LX:
Bit 1 reserved, only 60/66 MHz supported)
See Also: #01055 - #01057
Bitfields for Intel 82434LX/NX Secondary Cache Control: Bit(s) Description (Table 01057) 7-6 secondary cache size. 00 none. 01 reserved. 10 256K. 11 512K 5 SRAM type. 0 standard SRAMs. 1 burst SRAMs 4 secondary cache allocation. 0 cache only CPU reads of memory with CACHE# asserted. 1 cache all CPU reads of cacheable memory 3 Cache Byte Control. 0 use single write enable and per-byte select lines. 1 use per-byte write enables on the cache 2 (NX only) SRAM connectivity. 0 disable CCS[1:0]# / CCS1# functionality. 1 enable CCS[1:0]# functionality to de-select async SRAMs, placing them in a low-power standby mode. 1 enable CCS1# functionality for burst SRAMs, indicating the lack of an external address latch 1 (LX only) Secondary Cache Write Policy. 0 write-through. 1 write-back (NX is always in write-back mode) 0 Secondary Cache Enable
See Also: #01055 - #01058
Bitfields for Intel 82434LX/NX Host Read/Write Buffer Control: Bit(s) Description (Table 01058) 7-4 reserved 3 enable read-around-write 2 reserved 1 enable CPU-to-PCI posted writes 0 (LX only) enable CPU-to-memory posted writes. (NX always posts memory writes)
See Also: #01055 - #01057
Bitfields for Intel 82434LX/NX DRAM Control: Bit(s) Description (Table 01059) 7-6 (NX only) DRAM burst timing. 00 X-4-4-4 read/write (default). 01 X-4-4-4 read, X-3-3-3 write. 10 reserved. 11 X-3-3-3 read/write 5 parity error mask 4 0-Active RAS# mode 3 SMRAM enable (must be set to enable reg 72h) 2 Burst-of-Four Refresh 1 Refresh Type. =0 RAS#-only. =1 CAS#-before-RAS# 0 DRAM Refresh Enable
See Also: #01055
Bitfields for Intel 82434LX/NX Error Command register: Bit(s) Description (Table 01060) 7 assert SERR# on receiving target abort 6 assert SERR# on PCI data-write parity error 5 (NX only) assert SERR# on PCI data-read parity error 4 (NX only) assert SERR# on PCI address parity error 3 (NX only) assert PERR# on data parity error 2 enable L2 cache parity 1 enable SERR# on DRAM/L2 cache data parity error 0 assert PEN# on data reads; allow CPU to signal parity error via PCHK#
Notes: PCI command register bit 6 is master enable for bit 3;. PCI cmd bits 6 and 8 are the master enable for bits 7-4 and 1. Bits 1-0 = 10 is not permitted
See Also: #01055 - #01061
Bitfields for Intel 82434LX/NX Error Status register: Bit(s) Description (Table 01061) 7 reserved 6 PCI-write detected parity error 5 (NX only) PCI-read detected parity error 4 (NX only) PCI address parity error detected 3 main memory data parity error 2 L2 cache data parity error 1 reserved 0 Shutdown cycle detected
Note: Clear status bits by writing a 'one' bit to each bit to be cleared
See Also: #01060 - #01055
Bitfields for Intel 82434LX/NX Frame Buffer Range register: Bit(s) Description (Table 01062) 31-20 buffer offset (in 1MB increments; must be multiple of buffer set set by bits 3-0) 19-14 reserved 13 enable byte merging 12 128K VGA-range Attribute Enable. When set, bits 13,9,7 also apply to VGA memory range (Axxxx-Bxxxx) 11-10 reserved 9 no lock requests 8 reserved 7 enable transparent bufer writes 6-4 reserved 3-0 buffer size in MB (less 1); must be power of 2
Note: If bits 31-20=0, the frame buffer feature is disabled
See Also: #01055
Format of PCI Configuration data for Intel 82424 Cache Controller: Offset Size Description (Table 01063) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 0483h) 40h BYTE bus number 41h BYTE subordinate bus number 42h BYTE disconnect timer 50h BYTE host CPU selection 51h BYTE deturbo frequency control when deturbo mode is selected (see PORT 0CF9h), the chipset places a hold on the memory bus for a fraction of the time inversely proportional to the value in this register (i.e. C0h = 1/4, 80h = 1/2, 40h = 3/4, 20h = 7/8, etc.) 52h BYTE secondary cache control 53h BYTE write buffer control 54h BYTE PCI features control 55h BYTE DRAM Operation Mode Select 56h BYTE System Exception Handling 57h BYTE SMM Control Register 58h BYTE reserved 59h 7 BYTEs Programmable Attribute Map registers 0-6 (see also #01118) 60h 4 BYTEs DRAM Row Boundary registers 0-3 each register N indicates amount of memory in rows 0-N (each row is 64 bits wide) boundary register 3 (offset 63h) contains the total system memory, which may not exceed 128M 64h 4 BYTEs unused??? 68h WORD Memory Hole-0 6Ah WORD Memory Hole-1
Note: The above field names are those given by EduWARE's PCI Configuration Manager v1.2
See Also: #01055 - #01083 - #01108
Format of PCI Configuration data for Intel 82378 and 82379 ISA Bridges: Offset Size Description (Table 01064) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 0484h) (revision ID:
bits 7-4:
Reservedbits 3-0:
Revision 0011 82378ZB A0-step 1000 82379AB A0-step) 40h BYTE PCI Control (see #01065) 41h BYTE PCI Arbiter Control (see #01066) 42h BYTE PCI Arbiter Priority Control (see #01067) 43h BYTE (82378ZB) PCI Arbiter Priority Control Extension Registerbit 0:
Bank 3 fixed priority mode select (see also #01067) =0 REQ2# has higher priority =1 REQ3# has higher priority 44h BYTE MEMCS# Control (see #01068) 45h BYTE MEMCS# Bottom of Hole (address bits 23-16) 46h BYTE MEMCS# Top of Hole (address bits 23-16) 47h BYTE MEMCS# Top of Memory (address bits 28-21 == size in 2M increments, less 1) 48h BYTE ISA Address Decoder Control (see #01069) 49h BYTE ISA Address Decoder ROM Block Enable (see #01070) 4Ah BYTE ISA Address Decoder Bottom of Hole (address bits 23-16) 4Bh BYTE ISA Address Decoder Top of Hole (address bits 23-16) 4Ch BYTE ISA Controller Recovery Time (see #01087) 4Dh BYTE ISA Clock Divisor (see #01071) 4Eh BYTE Utility Bus Chip Select Enable A (see #01072) 4Fh BYTE Utility Bus Chip Select Enable B (see #01073) 50h 4 BYTEs reserved 54h BYTE MEMCS# Attribute Register #1 (see #01074) attributes for 16K blocks from C0000h-CFFFFh 55h BYTE MEMCS# Attribute Register #2 (see #01074) attributes for 16K blocks from D0000h-DFFFFh 56h BYTE MEMCS# Attribute Register #3 (see #01074) attributes for 16K blocks from E0000h-EFFFFh 57h BYTE (82378) Scatter/Gather Relocation Base Adress (see #01075) (82379AB) reserved 58h 8 BYTEs reserved 60h BYTE (82378ZB) IRQ0# Route Control (see #01076) 61h BYTE (82378ZB) IRQ1# Route Control (see #01076) 62h BYTE (82378ZB) IRQ2# Route Control (see #01076) 63h BYTE (82378ZB) IRQ3# Route Control (see #01076) 64h 12 BYTEs reserved 70h BYTE (82378) reserved (82379AB, write-only) PIC/APIC Configuration Control (see #01077) 71h BYTE (82378) reserved (82379AB, write-only) APIC Base Address Relocation (see #01078,MEM FEC00000h) 72h 14 BYTEs reserved 80h WORD BIOS timer base address (see PORT 0078h) bits 15-2 are bits 15-2 of BIOS timer port addressbit 1:
Reserved (0)bit 0:
Timer enabled (if disabled, other bits ignored) 82h 30 BYTEs unused??? A0h BYTE SMI Control (see #01079) A1h BYTE reserved A2h WORD SMI Enable (see #01080) A4h DWORD System Event Enable (SEE) (see #01081) A8h BYTE Fast-Off Timer (in minutes) A9h BYTE reserved AAh WORD active SMI Requests (see #01082) ACh BYTE (82378ZB) Clock Throttle STPCLK# Low Timer duration of STPCLK# low period in 32 microsecond units ADh BYTE reserved AEh BYTE (82378ZB) Clock Throttle STPCLK# High Timer duration of STPCLK# high period in 32 microsecond units AFh 81 BYTEs reserved
See Also: #01055 - #01167 - PORT 040Ah"82378ZB"
Bitfields for Intel 82378/82379 PCI Control: Bit(s) Description (Table 01065) 7 reserved (0) 6 DMA Reserved Page Register Aliasing Control. =0 alias PORT 80h-8Fh to PORT 90h-9Fh 5 Interrupt Acknowledge Enable. =0 ignore INTA cycles on the PCI bus, but still allow 8259 register access and poll-mode functions 4-3 Subtractive Decoding Sample Point. 00 slow sample point. 01 typical. 10 fast sample point. 11 reserved 2 PCI Posted Write Buffer Enable 1 ISA Master Line Buffer Configuration. =0 single-transaction mode. =1 eight-byte mode for ISA bus master transfers 0 DMA Line Buffer Configuration. =0 single-transaction mode. =1 eight-byte mode
See Also: #01064 - #01066
Bitfields for Intel 82378/82379 PCI Arbiter Control: Bit(s) Description (Table 01066) 7-5 reserveed (0) 4-3 Master Retry Timer. 00 disabled (retries never masked). 01 retries unmasked after 16 PCICLKs. 10 retries unmasked after 32 PCICLKs. 11 retries unmasked after 64 PCICLKs 2 Bus Park. =1 park CPUREQ# on PCI bus when 82378 detects PCI bus idle 1 Bus Lock. =0 resource lock. =1 Bus lock 0 Guaranteed Access Time. =1 ISA bus masters are guaranteed 2.5 microsecond CHRDY time-out
See Also: #01064 - #01065
Bitfields for Intel 82378/82379 PCI Arbiter Priority Control: Bit(s) Description (Table 01067) 7 bank 3 rotate control 6 bank 2 rotate control 5 bank 1 rotate control 4 bank 0 rotate control 3 bank 2 fixed priority mode select B 2 bank 2 fixed priority mode select A 1 bank 1 fixed priority mode select 0 bank 0 fixed priority mode select
Note: If both 'rotate' and 'fixed' bits are set for a given bank, that bank will be in rotating-priority mode
See Also: #01064 - #01066
Bitfields for Intel 82378/82379 MEMCS# Control Register: Bit(s) Description (Table 01068) 7-5 reserved (0) 4 MEMCS# Master Enable 3 write enable for 0F0000h-0FFFFFh 2 read enable for 0F0000h-0FFFFFh 1 write enable for 080000h-09FFFFh 0 read enable for 080000h-09FFFFh
See Also: #01064
Bitfields for Intel 82378/82379 ISA Address Decoder Control Register: Bit(s) Description (Table 01069) 7-4 ISA memory cycle forwarding to PCI. 0000-1111 = 1M-16M top of ISA memory; any accesses above programmed limit are forwarded to PCI bus 3-0 ISA/DMA memory cycle to PCI bus enables.
Bit 3:
896K-960K (E000h-EFFFh).Bit 2:
640K-768K (A000h-BFFFh).Bit 1:
512K-640K (8000h-9FFFh).Bit 0:
0K-512K (0000h-7FFFh)
See Also: #01064 - #01070
Bitfields for Intel 82378/82379 ISA Address Decoder ROM Block Enable: Bit(s) Description (Table 01070) 7 enable 880K-896K (EC00h-EFFFh) 6 enable 864K-880K (E800h-EBFFh) 5 enable 848K-864K (E400h-E7FFh) 4 enable 832K-848K (E000h-E3FFh) 3 enable 816K-832K (DC00h-DFFFh) 2 enabel 800K-816K (D800h-DBFFh) 1 enable 784K-800K (D400h-D7FFh) 0 enable 768K-784K (D000h-D3FFh)
Note: ISA accesses within any enabled ranges are forwarded to the PCI bus
See Also: #01064 - #01069
Bitfields for Intel 82378/82379 ISA Clock Divisor Register: Bit(s) Description (Table 01071) 7 reserved (0) 6 enable positive decode of upper 64K BIOS at 000F0000h-000FFFFFh, FFEF0000h-FFEFFFFFh, and FFFF0000h-FFFFFFFFh 5 coprocessor error enable. =1 FERR# is driven onto IRQ13 4 IRQ12/Mouse Function Enable. =0 standard IRQ12. =1 mouse 3 RSTDRV enable. =1 assert RSTDRV until this bit cleared (for use in changing ISA bus speed) 2-0 PCICLK-to-ISA SYSCLK divisor. 000 4. 001 3. Other reserved
See Also: #01064 - #01069
Bitfields for Intel 82378/82379 Utility Bus Chip Select A Register: Bit(s) Description (Table 01072) 7 extended BIOS enable (decode accesses to FFF80000h-FFFDFFFFh) 6 lower BIOS enable (decode accesses to E0000h-EFFFFh, FFEE0000h-FFEEFFFFh, and FFFE0000h-FFFEFFFFh) 5 (82378ZB) floppy disk primary/secondary address select. =1 use secondary address range 4 (82378ZB) IDE Decode enable 3,2 floppy disk address locations enable 1 keyboard controller address location enable. Enables I/O addresses 60h,62h,64h,66h (82378ZB) or 60h/64h (82379AB) 0 RTC address location enabled. =1 enable decode of I/O ports 70h-77h
See Also: #01064 - #01089 - #01073
Bitfields for Intel 82378ZB/82379 Utility Bus Chip Select B Register: Bit(s) Description (Table 01073) 7 configuration RAM decode enable. =1 permit write accesses to I/O port 0C00h and r/w to ports 08xxh 6 enable PORT 0092h 5-4 parallel port enable. 00 LPT1 (ports 03BCh-03BFh). 01 LPT2 (ports 0378h-037Fh). 10 LPT3 (ports 0278h-027Fh). 11 disabled 3-2 serial port B enable. 00 COM1 (03F8h-03FFh). 01 COM2 (02F8h-02FFh). 10 reserved. 11 port B disabled 1-0 serial port A enable. 00 COM1 (03F8h-03FFh). 01 COM2 (02F8h-02FFh). 10 reserved. 11 port A disabled
Note: If both serial ports are set to the same address, port B is disabled
See Also: #01064 - #01072 - PORT 0092h
Bitfields for Intel 82378/82379 MEMCS# Attribute Register 1/2/3: Bit(s) Description (Table 01074) 7 write-enable xC000h-xFFFFh expansion ROM 6 read-enable xC000h-xFFFFh expansion ROM 5 write-enable x8000h-xBFFFh expansion ROM 4 read-enable x8000h-xBFFFh expansion ROM 3 write-enable x4000h-x7FFFh expansion ROM 2 read-enable x4000h-x7FFFh expansion ROM 1 write-enable x0000h-x3FFFh expansion ROM 0 read-enable x0000h-x3FFFh expansion ROM
Note: X = C/D/E depending on the attribute register
See Also: #01064
Bitfields for Intel 82378ZB Scatter Gather Relocation Base Address: Bit(s) Description (Table 01075) 7-0 bits 15-8 of base address for scatter/gather I/O ports. (default 04h; low 8 bits of address are always 10h-3Fh)
See Also: #01064 - #01074 - #01076 - PORT 040Ah"82378ZB" - #P0039
Bitfields for Intel 82371/82378/82379 PCI IRQ Route Control Register: Bit(s) Description (Table 01076) 7 disable IRQ routing 6-4 reserved (0) 3-0 ISA IRQ number to which to route the PCI IRQ
Note: IRQs 0-2, 8, and 13 are reserved
See Also: #01064 - #01167 - #01100
Bitfields for Intel 82379AB PIC/APIC Configuration Control Register: Bit(s) Description (Table 01077) 7-2 reserved 1 SMI Routing Control. =1 SMI via APIC. =0 SMI via SMI# signal 0 INT Routing Control. =1 INT disabled (requires that APIC be enabled). =0 INT enabled
See Also: #01064 - #01078
Bitfields for Intel 82379AB/82371 APIC Base Address Relocation: Bit(s) Description (Table 01078) 7 reserved 6 (82379AB) reserved 6 (82371) A12 mask. =1 ignore address bit 12 in APIC address 5-0 bits 15-10 of APIC memory address (ORed with FEC00000h to form base address)
See Also: #01064 - #01167 - #01077 - MEM FEC00000h
Bitfields for Intel 82378/82379 SMI Control Register: Bit(s) Description (Table 01079) 7 reserved 6 (82378) reserved. (82379) require Stop Grant bus cycle before asserting STPCLK# 5-4 reserved 3 Fast-Off Timer freeze 2 STPCLK# scaling enable. =1 enable Clock Throttle bytes in PCI configuration space 1 STPCLK# signal enable. =1 assert STPCLK# on read from PORT 00B2h 0 SMI# Gate. =1 enable SMI# on system management interrupt
Notes: Bit 1 is cleared either with an explicit write of 0 here, or by any write to PORT 00B2h. Bit 0 does not affect the recording of SMI events, so a pending SMI will cause an immediate SMI# when the bit is set
See Also: #01064 - #01080 - #01081 - #01222 - PORT 00B2h
Bitfields for Intel 82371/82378/82379 SMI Enable Register: Bit(s) Description (Table 01080) 15-9 reserved 8 (82371SB only) Legacy USB SMI enable 7 APMC Write SMI enable. =1 generate SMI on write to PORT 00B2h 6 EXTSMI# SMI enable 5 Fast-Off Timer SMI enable 4 IRQ12 (PS/2 mouse) SMI enable 3 IRQ8 (RTC alarm) SMI enable 2 IRQ4 (COM1/COM3) SMI enable 1 IRQ3 (COM2/COM4) SMI enable 0 IRQ1 (keyboard) SMI enable
See Also: #01064 - #01079 - #01081 - #01167 - PORT 00B2h
Bitfields for Intel 82371/82378/82379 System Event Enable Register: Bit(s) Description (Table 01081) 31 Fast-Off SMI enable (system and break events) 30 (82379 only) Fast-Off Interrupt Enable (break events only) 30 (82371 only) INTR enable (break events only) 29 Fast-Off NMI enable (system and break events) 28 (82371SB only) Fast-Off APIC enable (break events only) 27 (82379 only) Fast-Off COM enable (system events only) 26 (82379 only) Fast-Off LPT enable (system events only) 25 (82379 only) Fast-Off Drive enable (system events only) 24 (82379 only) Fast-Off DMA enable (system events only) 23-16 reserved 15-3 Fast-Off IRQ (15-3) enable (system and break events) 2 reserved 1-0 Fast-Off IRQ (1-0) enable (system and break events)
Note: Any enabled system event restarts the Fast-Off Timer, thus preventing a Fast-Off powerdown; any enabled break event awakens the system from powerdown
See Also: #01064 - #01079 - #01080 - #01082 - #01167
Bitfields for Intel 82371/82378/82379 SMI Request Register: Bit(s) Description (Table 01082) 15-9 reserved 8 (82371SB only) Legacy USB SMI status 7 APM SMI Status (write to PORT 00B2h triggered SMI) 6 EXTSMI# SMI Status (EXTSMI# line triggered SMI) 5 Fast-Off Timer expired 4 IRQ12 triggered SMI 3 IRQ8 triggered SMI 2 IRQ4 triggered SMI 1 IRQ3 triggered SMI 0 IRQ1 triggered SMI
Note: Software must explicitly reset the appropriate bits
See Also: #01064 - #01081 - #01167
Format of PCI Configuration data for Intel 82425EX PSC: Offset Size Description (Table 01083) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 0486h) 40h BYTE PCI control register (see #01084) 41h 3 BYTEs ??? 44h BYTE host device control register (see #01085) 45h 3 BYTEs ??? 48h WORD PCI local-bus IDE control register (see #01086) 4Ah 2 BYTEs ??? 4Ch BYTE ISA I/O recovery timer register (see #01087) 4Dh BYTE part revision register (see #01088) 4Eh BYTE X-bus Chip Select A register (see #01089) 4Fh BYTE X-bus Chip Select B register??? (see also #01102) 50h BYTE host select register 51h BYTE deturbo frequency control register when deturbo mode is selected (see PORT 0CF9h), the chipset places a hold on the memory bus for a fraction of the time inversely proportional to the value in this register (i.e. C0h = 1/4, 80h = 1/2, 40h = 3/4, 20h = 7/8, etc.) 52h WORD secondary (L2) cache control register 54h 2 BYTEs ??? 56h WORD DRAM control register 58h BYTE ??? 59h 7 BYTEs Programmable Attribute Map (PAM) registers 0-6 (see also #01118) 60h 5 BYTEs DRAM row boundary registers 0-4 each register N indicates amount of memory in rows 0-N (each row is 64 bits wide); the fifth row of memory (if implemented) must contain either 8M or 16M, depending on system configuration boundary register 4 (offset 64h) contains the total system memory, which may not exceed 128M 65h BYTE ??? 66h BYTE PIRQ route control register 0 67h BYTE PIRQ route control register 1 68h BYTE DRAM memory hole register 69h BYTE top of memory 6Ah 6 BYTEs ??? 70h BYTE SMRAM control register 71h 47 BYTEs unused??? A0h BYTE SMI control register A1h BYTE ??? A2h WORD SMI enable register A4h DWORD system event enable A8h BYTE fast off timer register A9h BYTE ??? AAh WORD SMI request register ACh BYTE clock throttle STPCLK# low timer ADh BYTE unused??? AEh BYTE clock throttle STPCLK# high timer AFh BYTE ??? B0h 80 BYTEs unused???
See Also: #00878 - #01063 - #01055 - #01108 - #01167
Bitfields for Intel 82425EX PCI control register: Bit(s) Description (Table 01084) 0 CPU-to-PCI byte merging 1 CPU-to-PCI bursting enable 2 PCI posted-write buffer enable 4-3 subtractive decode sampling point. 00 slow. 01 typical. 10 fast. 11 reserved 5 DRAM parity error enable 6 target abort error enable 7 reserved
See Also: #01083 - #01085 - #01086 - #01087
Bitfields for Intel 82425EX host device control register: Bit(s) Description (Table 01085) 0 HRDY# maximum signal sampling point. 0 slow timing. 1 fast timing 1 HDEV# signal sampling point. 0 slow timing. 1 fast timing 2 host device present 7-3 reserved
See Also: #01083 - #01084
Bitfields for Intel 82425EX local-bus IDE control register: Bit(s) Description (Table 01086) 1-0 primary/secondary PCI IDE enable. 00 IDE disabled. 01 primary (ports 01F0h-01F7h,03F6,03F7h). 10 secondary (ports 0170h-017Fh,0376h,0377h). 11 reserved 3-2 fast timing bank drive select 1. Bit 2 = drive 0 enabled. Bit 3 = drive 1 enabled 5-4 IORDY sample point Enable Drive Select. Bit 4 = drive 0 enabled. Bit 5 = drive 1 enabled 7-6 reserved 9-8 IORDY sample point. 00 6 clocks. 01 5 clocks. 10 4 clocks. 11 3 clocks 12-10 recover time (000 = 8 PCI clocks, 001 = 7, ..., 101 = 3, 110/111 = 3) 15-13 reserved
See Also: #01083 - #01084
Bitfields for Intel chipset ISA I/O recovery timer register: Bit(s) Description (Table 01087) 7 (82425EX/82371) DMA reserved page register aliasing disable. =0 ports 0090h-009Fh alias ports 0080h-008Fh. =1 ports 0090h-009Fh forwarded to ISA bus 6 8-bit I/O recovery enable 5-3 8-bit I/O recovery time. 000 = 8 SYSCLKs. 001-110 = 1-7 SYSCLKs 2 16-bit I/O recovery enable 1-0 16-bit I/O recovery time. 00 = 4 SYSCLKs. 01-11 = 1-3 SYSCLKs
See Also: #01064 - #01083 - #01084 - #01167 - #01170
Bitfields for Intel 82425EX part revision register: Bit(s) Description (Table 01088) 7-5 fabrication house identifier (read-only) 4 E0000h-EFFFFh ISA-to-main-memory forwarding enabled 3-0 revision ID (read-only)
See Also: #01083 - #01089
Bitfields for Intel 82425EX/82371 X-bus Chip Select A register: Bit(s) Description (Table 01089) 7 extended BIOS enabled at FFF80000h-FFFDFFFFh 6 lower (E000h) BIOS enabled 5 trigger IRQ13 on FERR# 4 IRQ12 mouse function enabled 3 (82371AB only) alias accesses to PORTs 63h/65h/67h to 61h. (else) reserved (0) 2 BIOS memory write protect 1 keyboard controller addresses (60h,62h,64h,66h) enabled 0 RTC addresses (70h-77h) enabled
See Also: #01083 - #01167 - #01088 - #01102
Format of PCI Configuration Data for Intel 82380AB PCI-ISA Bridge: Offset Size Description (Table 01090) 00h 64 BYTEs header (see #00878) (vender ID 8086h, device ID 123Ch) 40h BYTE I/O Recovery Register (see #01091) 41h BYTE reserved 42h BYTE MISA Error Status (see #01092) 43h 189 BYTEs reserved
See Also: #00873 - #01093
Bitfields for Intel 82380AB I/O Recovery Register: Bit(s) Description (Table 01091) 7 SYSCLK select. 0 SYSCLK = PCICLK/4. 1 SYSCLK = PCICLK/3 6 enable 8-bit I/O recovery 5-3 additional recovery time for 8-bit I/O cycles, in SYSCLKs 2 enable 16-bit I/O recovery 1-0 additional recovery time for 16-bit I/O cycles, in SYSCLKs
See Also: #01090
Bitfields for Intel 82380AB MISA error status: Bit(s) Description (Table 01092) 7-3 reserved 2 IOCHK# asserted 1 reserved 0 illegal byte lane combination for PCI I/O detected
See Also: #01090
Format of PCI Configuration data for Intel 82380FB PCI-PCI Bridge (MPCI2): Offset Size Description (Table 01093) 00h 64 BYTEs header type 1 [bridge] (see #00878) (vendor ID 8086h, device ID 124Bh) 40h BYTE Connector Control (see #01094) 41h BYTE Connector Event (see #01095) 42h 2 BYTEs reserved 44h WORD Serial Bus Interface/Burst Enable (see #01096) 46h BYTE MPCI2 Miscellaneous Status (see #01097) 47h 5 BYTEs reserved 4Ch WORD Special Message Encode encoded message portion of Special Cycle forwarded by MPCI2 4Eh 178 BYTEs reserved
See Also: #00873 - #01090
Bitfields for Intel 82380FB Connector Control register: Bit(s) Description (Table 01094) 7-4 reserved 3 QEN2 output signal 2 QEN1 output signal 1-0 reserved
See Also: #01093
Bitfields for Intel 82380FB Connector Event register: Bit(s) Description (Table 01095) 7 reserved (1) 6 activate power-no suspend 5 (read-only) inverted state of MISAEN pin 4 (read-only) inverted state of DSTYP pin 3 undocking permit. Software should set this bit for at least 32 microseconds; when this bit is then cleared, the MPCI2 pulses the OPENACK signal for 256 us to tell external hardware to "eject" the notebook 2 reserved (1) 1 system is docked 0 open requested
See Also: #01093
Bitfields for Intel 82380FB Serial Interface/Burst Enable register: Bit(s) Description (Table 01096) 15-13 reserved 12 enable SERR# on discarding of posted write data 11 reserved 10 SDATA signal direction (0 = output, 1 = input) 9 enable write posting 8 enable read bursting 7 enable upstream blind prefetching 6 reserved 5 SDATA signal state (read when bit 10 set, write when bit 10 clear) 4 SDIN signal state 3 do not pulse P_SERR# when S_PERR# is asserted 2 cascade/frame determination delay (0 = 20 P_CLKs, 1 = 10 P_CLKs) 1 serial EEPROM chip select 0 serial EEPROM clock
See Also: #01093
Bitfields for Intel 82380FB MPCI2 Miscellaneous Status register: Bit(s) Description (Table 01097) 7-1 reserved 0 (write-clear) P_SERR# was asserted due to invalidation of posted write
See Also: #01093
Format of PCI Configuration Data for Intel 82439HX: Offset Size Description (Table 01098) 00h 64 BYTEs header (see #00878) (vender ID 8086h, device ID 1250h) (revision ID 00h = A0 stepping) 40h 16 BYTEs reserved 50h BYTE PCI Control (see #01110) 51h BYTE reserved 52h BYTE cache control (see #01112) 53h 3 BYTEs reserved 56h BYTE DRAM extended control (see #01115) 57h BYTE DRAM control (see #01116) 58h BYTE DRAM timing (see #01117) 59h 7 BYTEs Programmable Attribute Map registers 0-6 (see #01118) 60h 8 BYTEs DRAM Row Boundary registers 0-7 each register N indicates cumulative amount of memory in rows 0-N (each 64 bits wide), in 4M units 68h BYTE DRAM Row Type (see #01119) bits 0-7 indicate whether each row 0-7 contains EDO DRAM instead of page-mode DRAM 69h BYTE ??? 6Ah 8 BYTEs reserved 72h BYTE System Management RAM control (see #01123) 73h 29 BYTEs reserved 90h BYTE Error Command (see #01126) 91h BYTE Error Status (see #01127) (read-only) 92h BYTE Error Syndrome (read-only) latest non-zero ECC error syndrome 93h 109 BYTEs reserved
See Also: #01108 - #01229
Format of PCI Configuration Data for Intel 82439TX "MTXC": Offset Size Description (Table 01099) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 7100h) (revision ID 00h = A0 stepping) 40h 15 BYTEs reserved 4Fh BYTE Arbitration Control register (see #01109) 50h BYTE PCI Control register (see #01110) 51h BYTE reserved 52h BYTE Cache Control register (see #01112) 53h BYTE Extended Cache Control register (see #01113) 54h WORD SDRAM Control Register (see #01114) 56h BYTE DRAM Extended Control register (see #01115) 57h BYTE DRAM Control register (see #01116) 58h BYTE DRAM Timing register (see #01117) 59h 7 BYTEs Programmable Attribute Map registers 0-6 (see #01118) 60h 6 BYTEs DRAM Row Boundary registers 0-5 each register N indicates cumulative amount of memory in rows 0-N (each 64 bits wide), in 4M units 66h BYTE reserved 67h BYTE DRAM Row Type High register (see #01213) 68h BYTE DRAM Row Type Low register (see #01119) 69h 7 BYTEs reserved 70h BYTE Multi-Transaction Timer register number of PCLKs guaranteed to the current agent before the 82439TX will grant the bus to another PCI agent on request 71h BYTE Extended System Management RAM Control register (see #01149) 72h BYTE System Management RAM Control register (see #01123) 73h 6 BYTEs reserved 79h BYTE Miscellaneous Control register (see #01128) 7Ah 134 BYTEs reserved
Note: The Intel 82439TX chipset uses PCI configuration mechanism #1
See Also: #00873 - PORT 0CF8h
Format of PCI Configuration Data for Intel 82371AB (PIIX4), ISA Bridge: Offset Size Description (Table 01100) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 7110h) 40h 12 BYTEs reserved 4Ch BYTE ISA I/O recovery timer (see #01101) 4Dh BYTE reserved 4Eh WORD X-Bus Chip Select (see #01089,#01102) 50h 16 BYTEs reserved 60h BYTE PIRQA route control (see #01076) 61h BYTE PIRQB route control (see #01076) 62h BYTE PIRQC route control (see #01076) 63h BYTE PIRQD route control (see #01076) !!!intel\29056201.pdf p.59 64h BYTE serial IRQ control 65h 4 BYTEs reserved??? 69h BYTE top of memory 6Ah WORD miscellaneous status 6Ch 10 BYTEs reserved??? 76h BYTE motherboard device DMA control 0 77h BYTE motherboard device DMA control 1 78h 9 BYTEs reserved??? 80h BYTE APIC base address relocation 81h BYTE reserved??? 82h BYTE deterministic latency control 83h 13 BYTEs reserved??? 90h WORD PCI DMA configuration 92h WORD distributed DMA (channels 0-3) slave base pointer 94h WORD distributed DMA (channels 5-7) slave base pointer 96h 26 BYTEs reserved??? B0h DWORD general configuration B4h 23 BYTEs reserved??? CBh BYTE real-time clock configuration CCh 52 BYTEs reserved
See Also: #00873 - #01103 - #01104 - #01105
Bitfields for Intel PIIX4 ISA I/O recovery timer: Bit(s) Description (Table 01101) 7 disable aliasing PORTs 90h-9Fh into 80h-8Fh (except PORT 0092h) 6 enable 8-bit I/O recover timer in bits 5-3 5-3 additional 8-bit I/O recovery time (added to 3.5 SYSCLK minimum). 000 = 8 SYSCLKs, else N SYSCLKs 2 enable 16-bit I/O recovery timer in bits 1-0 1-0 additional 16-bit I/O recovery time (added to 3.5 SYSCLK minimum). 00 = 3 SYSCLKs. 01 = 1 SYSCLK. 10 = 2 SYSCLKs. 11 = 4 SYSCLKs
See Also: #01100
Bitfields for Intel 82371 X-Bus Chip Select Enable (high byte): Bit(s) Description (Table 01102) 7-3 reserved 2 (82371AB) enable positive PCI decode for Micro Controller at PORTs 62h and 66h 1 (82371AB) enable one-megabyte extended BIOS (FFF00000h-FFF7FFFFh are forwarded to ISA bus, aliased to top of 16M region) 0 enable I/O APIC
See Also: #01089
Format of PCI Configuration Data for Intel 82371AB (PIIX4), IDE Controller: Offset Size Description (Table 01103) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 7111h) 20h DWORD I/O base address (for 16 contiguous PORTs) !!!intel\29056201.pdf p.89 40h WORD primary channel timing register 42h WORD secondary channel timing register 44h BYTE slave IDE timing 45h 3 BYTEs reserved??? 48h BYTE Ultra DMA/33 control 49h BYTE reserved??? 4Ah WORD Ultra DMA/33 timing 4Ch 180 BYTEs reserved
See Also: #00873 - #01100 - #01104 - #01105
Format of PCI Configuration Data for Intel 82371AB (PIIX4), USB Controller: Offset Size Description (Table 01104) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 7112h) 20h DWORD I/O base address (for 32 contiguous PORTs) !!!intel\29056201.pdf p.102 40h 32 BYTEs reserved 60h BYTE USB specification release number 00h pre-release 1.0 10h release 1.0 61h 95 BYTEs reserved C0h WORD legacy support C2h 61 BYTEs reserved FFh BYTE miscellaneous support
See Also: #00873 - #01100 - #01103 - #01105
Format of PCI Configuration Data for Intel 82371AB (PIIX4), Power Management: Offset Size Description (Table 01105) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 7113h) 40h DWORD base address of power-management I/O ports (same format as PCI base addresses; low bit hardwired to 1) 44h DWORD initial counts of device 0-11 idle timers 48h DWORD !!!intel\29056201.pdf p.117 4Ch DWORD general-purpose input control 50h 3 BYTEs "device resource D" 53h BYTE unused??? 54h DWORD device activity event selection A 58h DWORD device activity event selection B 5Ch DWORD "device resource A" 60h DWORD "device resource B" 64h DWORD "device resource C" 68h 3 BYTEs "device resource E" 6Bh 5 BYTEs unused??? 70h 3 BYTEs "device resource G" 73h BYTE unused??? 74h DWORD "device resource H" 78h DWORD "device resource I" 7Ch DWORD "device resource J" 80h BYTE miscellaneous power management 81h 15 BYTEs unused??? 90h DWORD base address for SMBus I/O ports (same format as PCI base addresses; low bit hardwired to 1) 94h ... D2h BYTE SMBus host configuration D3h BYTE SMBus slave command D4h BYTE SMBus slave shadow port 1 address D5h BYTE SMBus slave shadow port 2 address D6h BYTE SMBus revision D7h
See Also: #00873 - #01100 - #01103 - #01104
Format of PCI Configuration Data for Intel 82437MX: Offset Size Description (Table 01106) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 1235h) 40h 16 BYTEs reserved 50h BYTE PCI Control (see #01111) 51h BYTE reserved 52h BYTE cache control (see #01112) 53h 4 BYTEs reserved 57h BYTE DRAM Control (see #01116) 58h BYTE DRAM timing (see #01117) 59h 7 BYTEs Programmable Attribute Map registers 0-6 (see #01118) 60h 4 BYTEs DRAM Row Boundary Registers 0-3 each register N indicates cumulative amount of memory in rows 0-N, in 4M units (each row is 64 bits wide) 64h 4 BYTEs reserved 68h BYTE DRAM Row Type (see #01121) 69h 9 BYTEs reserved 72h BYTE System Management RAM control (see #01123) 73h 141 BYTEs reserved
See Also: #01108 - #01107
Format of PCI Configuration Data for Intel 82437FX: Offset Size Description (Table 01107) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 122Dh) (see #00873) 40h 16 BYTEs reserved 50h BYTE PCI Control (see #01111) 51h BYTE reserved 52h BYTE cache control (see #01112) 53h 4 BYTEs reserved 57h BYTE DRAM Control (see #01116) 58h BYTE DRAM timing (see #01117) 59h 7 BYTEs Programmable Attribute Map registers 0-6 (see #01118) 60h 5 BYTEs DRAM Row Boundary Registers 0-4 each register N indicates cumulative amount of memory in rows 0-N, in 4M units (each row is 64 bits wide) 65h 3 BYTEs reserved 68h BYTE DRAM Row Type (see #01121) 69h 9 BYTEs reserved 72h BYTE System Management RAM control (see #01123) 73h 141 BYTEs reserved
See Also: #01106 - #01108
Format of PCI Configuration Data for Intel 82437VX: Offset Size Description (Table 01108) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 7030h) (revision ID 00h = A0 stepping) 40h 15 BYTEs reserved 4Fh BYTE arbitration control (see #01109) 50h BYTE PCI Control (see #01110) 51h BYTE reserved 52h BYTE cache control (see #01112) 53h BYTE cache control extensions (see #01113) 54h WORD SDRAM control (see #01114) 55h BYTE reserved 56h BYTE DRAM extended control (see #01115) 57h BYTE DRAM control (see #01116) 58h BYTE DRAM timing (see #01117) 59h 7 BYTEs Programmable Attribute Map registers 0-6 (see #01118) 60h 5 BYTEs DRAM Row Boundary registers 0-4 each register N indicates amount of memory in rows 0-N in 4M units (each row is 64 bits wide); the fifth row of memory (if implemented) must contain either 8M or 16M, depending on system configuration boundary register 4 (offset 64h) contains the total system memory, which may not exceed 128M 65h 2 BYTEs reserved 67h BYTE DRAM Row Type (high) defines memory type in DRAM row 4 in bits 4,0 (see #01119) 68h BYTE DRAM Row Type (low) (see #01119) 69h BYTE PCI TRDY timer (see #01122) 6Ah 6 BYTEs reserved 70h BYTE Multi-Transaction Timer number of PCLKs guaranteed to the current agent before the 82437 will grant the bus to another PCI agent on request 71h BYTE reserved 72h BYTE System Management RAM control (see #01123) 73h BYTE shared memory buffer control (see #01124) 74h BYTE shared memory buffer start address, in 0.5MB units end address is top-of-memory at offset 64h or start of an enabled PCI memory hole when top-of-memory is 16M 76h 2 BYTEs reserved 78h BYTE graphics controller latency timers (see #01125) 79h 135 BYTEs reserved
See Also: #00873 - #01063 - #01083 - #01098 - #01106
Bitfields for Intel 82437VX,82439TX Arbitration Control register: Bit(s) Description (Table 01109) 7 extended CPU-to-PIIX PHLDA# signalling enabled 6-0 (82439TX) reserved 6-4 reserved 3 (82437VX) CPU priority enable. =1 CPU gets PCI bus after two PCI slots. =0 CPU gets PCI bus after three PCI slots 2-0 reserved
See Also: #01099 - #01108 - #01110
Bitfields for Intel 82437VX,82439HX/TX PCI Control register: Bit(s) Description (Table 01110) 7-4 reserved (82437VX,82439TX) 7 DRAM ECC/Parity Select (82439HX). =1 ECC. =0 parity 6 ECC TEST enable (82439HX) 5 shutdown to port 92h (82439HX). =1 send 01h to PORT 0092h on Shutdown special cycle on host bus 4 dual-processor NA# enable (82439HX) 3 PCI Concurrency Enable. =1 CPU can access DRAM/L2 during non-PIIX PCI master cycles. =0 CPU kept off PCI bus during all PCI bus-master cycles 2-0 reserved (82437VX,82439TX) 2 SERR# Output Type (82439HX only). =1 SERR# is actively driven high when negated. =0 SERR# is PCI-compatible open-drain output 1 reserved 0 Global TXC Enable (82439HX only). =1 enable new 82439HX features
See Also: #01099 - #01108 - #01098 - #01112 - #01111
Bitfields for Intel 82437FX/82437MX PCI Control register: Bit(s) Description (Table 01111) 7-5 CPU inactivity timer (in PCI Clocks less 1) 4 reserved 3 enable PCI Peer Concurrency. =1 CPU can access DRAM/L2 during non-PIIX PCI master cycles. =0 CPU kept off PCI bus during all PCI bus-master cycles 2 disable PCI Bursting 1 disable PCI Streaming 0 disable Bus Concurrency
See Also: #01106 - #01107 - #01110
Bitfields for Intel 82437,82439HX/TX cache control register: Bit(s) Description (Table 01112) 7-6 secondary cache size. 00 none. 01 256K. 10 512K. 11 reserved 5-4 L2 RAM type. 00 pipelined burst SRAM/DRAM. 01 reserved. 10 asynchronous SRAM (82437FX/MX/VX,82439TX only). 11 two banks of pipelined burst cache 3 NA disable. =1 never assert NA# pin 2 reserved (82437FX/MX/VX,82439TX) 2 Extended Cacheability Enable (82439HX). =1 cache up to 512M. =0 cache only first 64M 1 Secondary Cache Force Miss or Invalidate. =1 force all memory accesses to bypass L2 cache 0 First Level Cache Enable. =1 all memory accesses made non-cacheable by CPU L1 cache
See Also: #01099 - #01108 - #01098 - #01110 - #01113 - #01114 - #01106
Bitfields for Intel 82437VX,82439TX cache control extensions register: Bit(s) Description (Table 01113) 7-6 reserved 5 DRAM cache detected (read-only) 4-0 DRAM cache refresh timer. Number of HCLKs 82437VX,82439TX remains idle during DRAM cache refresh
See Also: #01099 - #01108 - #01112
Bitfields for Intel 82437VX,82439TX SDRAM control register: Bit(s) Description (Table 01114) 15-9 reserved 8-6 Special SDRAM Mode Select. 000 normal mode (default). 001 enable NOP command. 010 enable All Banks Precharge command. 011 enable Mode Register Command. 100 enable CBR Cycle. 101 reserved. 11x reserved 5 (82437VX) reserved 5 (82439TX) RAS# to CAS# Override. =1 and CAS# latency=0, RAS# to CAS# is delayed 2 HCLKs. =0 RAS# to CAS# delay determined solely by CAS# latency setting 4 CAS# latency. =1 latency is 2 for all SDRAM cycles. =0 latency is 3 3 RAS# precharge and refresh timing. =0 slower. =1 faster 2 reserved 1 (82437VX) reserved 1 (82439TX) 64-Mbit Technology Enable. =1 supports 64M-bit SDRAM devices. =0 supports 64M-bit EDO/FPM devices only 0 reserved
See Also: #01099 - #01108 - #01112
Bitfields for Intel 82437VX,82439HX/TX DRAM extended control register: Bit(s) Description (Table 01115) 7 reserved 6 (VX/TX) refresh RAS# assertion length (0=4 clocks, 1=5 clocks) 5 (VX/TX) Fast EDO Path Select 4 Speculative Leadoff Disable 3 (82439HX) Turn-Around Insertion Enable. =1 insert one extra clock of turnaround time after asserting MWE# 2-1 Memory Address Drive Strength.
82437VX:
82439HX: 82439TX: 00 reserved 00 8mA 00 10mA/10mA (MA/MWE#) 01 10mA (default) 01 8mA/12mA (MAA/MWE#) 01 10mA/16mA (MA/MWE#) 10 16mA 10 12mA/8mA (MAA/MWE#) 10 16mA/10mA (MA/MWE#) 11 reserved 11 12mA 11 16mA/16mA (MA/MWE#) 0 (82437VX) DRAM Symmetry Detect Mode. (used to force some memory address lines to fixed value for detecting DRAM symmetry row-by-row) 0 (82439HX) 64MBit Mode Enable. =1 enable support for 64M SIMMs 0 (82439TX) reserved
See Also: #01099 - #01108 - #01098 - #01116
Bitfields for Intel 82437,82439HX/TX DRAM control register: Bit(s) Description (Table 01116) 7-6 DRAM Hole Enable. 00 none. 01 512K-640K. 10 15M-16M (82437FX/MX/VX only). 11 14M-16M (82437VX,82439TX only) 5 reserved 4 (82437MX only) refresh type during Suspend. =1 self-refreshing DRAMs in system. =0 CAS-before-RAS refresh. (82439TX only) Enhanced Paging disabled 3 EDO Detect Mode enable. (used to detect whether memory is EDO bank-by-bank) 2-0 DRAM refresh rate FX/VX/HX MX TX. 000 disabled 15.6 us disabled. 001 50 MHz 31.2 us 15.6 us. 010 60 MHz 62.4 us 31.2 us. 011 66 MHz 125 us 64.4 us. 100 reserved 250 us 125 us. 101 reserved reserved 256 us. 1xx reserved reserved reserved
See Also: #01099 - #01108 - #01098 - #01115 - #01106
Bitfields for Intel 82437FX/MX/VX,82439HX/TX DRAM timing register: Bit(s) Description (Table 01117) 7 (82437FX,82439TX) reserved 7 (82437MX) MA[11:2] buffer strength. =0 8mA. =1 12mA 7 (82437VX) MA-to-RAS# Delay. =1 one clock. =0 two clocks 7 (82439HX) Turbo Read Leadoff. =1 bypass first register in DRAM data pipeline, saving one clock. (may only be set in a cacheless configuration) 6-5 DRAM Read Burst Timing. 00 x444 (EDO and Standard Page Mode). 01 x333 (EDO), x444 (SPM). 10 x222 (EDO), x333 (SPM). 11 x322 (EDO), x333 (SPM) (82437VX only). 11 reserved (other) 4-3 DRAM Write Burst Timing. 00 x444. 01 x333. 10 x222. 11 reserved 2 (82439TX) reserved 2 RAS-to-CAS Delay. =1 two clocks. =0 three clocks 1-0 DRAM Leadoff Timing. 82437FX/MX Read Leadoff Write Leadoff RAS# Precharge 00 8 6 3 01 7 5 3 10 8 6 4 11 7 5 4. 82437VX,82439TX Read Write Leadoff RAS# Precharge 00 11 7 3 01 10 6 3 10 11 7 4 11 10 6 4. 82439HX Read Leadoff Write Leadoff RAS# Precharge 00 7 6 3 01 6 5 3 10 7 6 4 11 6 5 4
See Also: #01099 - #01108 - #01116 - #01106 - #01107
Bitfields for Intel 8243x/8244x Programmable Attribute Map Register: Bit(s) Description (Table 01118) 7 reserved 6 cache enable (region 1) 5 write enable (region 1) 4 read enable (region 1) 3 reserved 2 cache enable (region 0) 1 write enable (region 0) 0 read enable (region 0)
Notes: Each programmable attribute map register controls two memory regions at the top of the first megabyte of memory. For the Intel 82441FX and 82443BX/LX, bits 6 and 2 are reserved, as cacheability is set using the Pentium Pro/II/Celeron's MTRR registers (see MSR 000000FEh). Intel 82434,82437FX/MX/VX,82439HX,82441FX,82443EX/LX PAM registers/regions:
PAM0 low:
Reserved [*]PAM0 hi:
Segment F000-FFFFPAM1 low:
Segment C000-C3FFPAM1 hi:
Segment C400-C7FFPAM2 low:
Segment C800-CBFFPAM2 hi:
Segment CC00-CFFFPAM3 low:
Segment D000-D3FFPAM3 hi:
Segment D400-D7FFPAM4 low:
Segment D800-DBFFPAM4 hi:
Segment DC00-DFFFPAM5 low:
Segment E000-E3FFPAM5 hi:
Segment E400-E7FFPAM6 low:
Segment E800-EBFFPAM6 hi:
Segment EC00-EFFF. [*] on the 82434 (and possibly other Intel chipsets), the low nybble of PAM0 controls segment 8000-9FFF
See Also: #01055 - #01108 - #01098 - #01099 - #01229 - #01106 - #01107 - #01142 - #01129
Bitfields for Intel 82437VX,82439TX DRAM Row Type register: Bit(s) Description (Table 01119) 7,3 row 3 type 6,2 row 2 type 5,1 row 1 type 4,0 row 0 type. 00 SPM DRAM. 01 EDO DRAM. 10 SDRAM. 11 reserved
See Also: #01099 - #01108 - #01118 - #01213
Bitfields for Intel 82439TX DRAM Row Type high register: Bit(s) Description (Table 01213) 7 Host Frequency detection. =1 66MHz Bus. =0 60MHz bus 5,1 DRAM Row 5 type 4,0 DRAM ROW 4 type. 00 SPM. 01 EDO. 10 SDRAM. 11 reserved 6,3 reserved 2 Memory Address select Enabled
See Also: #01099 - #01119
Bitfields for Intel 82437FX/82437MX DRAM Row Type register: Bit(s) Description (Table 01121) 7-4 reserved 3-0 DRAM Row N is EDO instead of page-mode DRAM
See Also: #01106 - #01107
Bitfields for Intel 82437VX PCI TRDY timer: Bit(s) Description (Table 01122) 7-3 reserved 2-0 TRDY timeout value. 000 2 PCICLKs. 001 4 PCICLKs. 010 6 PCICLKs. 011 8 PCICLKs. 1xx reserved
See Also: #01108 - #01123
Bitfields for Intel 82437,82439HX/TX,82443BX/EX/LX SMRAM control register: Bit(s) Description (Table 01123) 7 reserved 6 SMM Space Open. =1 make SMM DRAM visible even when not in SMM if bit 4 =0 5 SMM Space Closed. =1 no data references permitted to SMM DRAM even in SMM 4 SMM Space Locked. =1 force bits 4 and 6 to become read-only; and clear bit 6 3 SMRAM Enable. =1 128K DRAM are accessible for use at A000 while in SMM 2-0 SMM Space Base Segment. 010 segment A000-BFFF. 100 segment C000-CFFF (82437MX,82443EX only). Other reserved
Note: Bits 5 and 6 must never both be set at the same time
See Also: #01099 - #01108 - #01098 - #01124 - #01106 - #01107 - #01142 - #01129
Bitfields for Intel 82437VX Shared Memory Buffer control register: Bit(s) Description (Table 01124) 7-2 reserved 1 enable shared memory buffer 0 redirect shared memory buffer access. =0 treat SMB area as a hole in system DRAM
See Also: #01108 - #01123 - #01125
Bitfields for Intel 82437VX Graphics Controller Latency Timer: Bit(s) Description (Table 01125) 7-6 reserved 5-3 GC latency for PCI reads (in 4 HCLK multiples) (default=100) 2-0 GC latency for CPU and PCI writes (in 4 HCLK multiples) (default=011)
See Also: #01108 - #01124
Bitfields for Intel 82439HX Error Command register: Bit(s) Description (Table 01126) 7 SERR# duration. =0 one PCI clock. =1 until error flags are cleared 6-3 reserved 2 force bad parity on multiple-bit uncorrectable error 1 assert SERR# on multiple-bit uncorrectable error 0 assert SERR# on single-bit correctable error
See Also: #01098 - #01127
Bitfields for Intel 82439HX Error Status register: Bit(s) Description (Table 01127) 7-5 DRAM row associated with multi-bit error 4 multi-bit uncorrectable error occurred (write 1 bit to clear) 3-1 DRAM row associated with single-bit correctable error 0 single-bit correctable error occurred (write 1 bit to clear)
See Also: #01098 - #01126
Bitfields for Intel 82439TX miscellaneous control register: Bit(s) Description (Table 01128) 7 reserved 6 ACPI control register enable 5 Suspend refresh type (EDO/FPM DRAM only). =1 Self refresh (Always for SDRAM). =0 CBR refresh 4 Normal refresh enable. When set to 1, 82439TX switches from suspend refresh to normal refresh 3 reserved 2 Internal clock control disable. =1 disable. =0 enable Disables 82439TX internal clocks during suspend, reducing power consumption. 1-0 reserved
See Also: #01099
Format of PCI configuration for Intel 82443EX/LX Device 0 (Host-PCI): Offset Size Description (Table 01129) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 7180h) chipset is 82443EX if revision >= 03h 40h 16 BYTEs reserved 50h WORD PAC Configuration register (See #01131) 52h BYTE reserved 53h BYTE Data Buffer Control register (see #01132) 54h BYTE reserved 55h WORD DRAM Row Type register (see #01133) 57h BYTE DRAM Control register (see #01134) 58h BYTE DRAM Timing register (see #01135) 59h 7 BYTEs PAM Configuration registers 0-6 (See #01118) 60h 8 BYTEs DRAM Row Boundary registers 0-7 each register indicates top of memory for a particular row, in 8MB units; DIMMs use two rows each, with single-sided DIMMs leaving the odd-numbered rows unpopulated 68h BYTE Fixed DRAM Hole Control register (see #01147) 69h BYTE reserved 6Ah WORD DRAM Extended Mode Select register (see #01136) 6Ch DWORD Memory Buffer Strength Control register (see #01137) 70h BYTE Multi-Transaction Timer register (see #01140) 71h BYTE reserved 72h BYTE System Management RAM Control register (see #01123) 73h 29 BYTEs reserved 90h BYTE Error Command register (see #01156) 91h BYTE Error Status 0 register (see #01138) 92h BYTE Error Status 1 register (see #01139) 93h BYTE Reset Control Register (see #01239) 94h 12 BYTEs reserved A0h DWORD AGP Capability register (see #01158) A4h DWORD AGP Status register (see #01159) A8h DWORD AGP Command register (see #01160) ACh 4 BYTEs reserved B0h DWORD AGP Control register (see #01161) B4h BYTE Arpeture Size Control register (see #01162) B5h 3 BYTEs reserved B8h DWORD Arpeture Translation Table Base register (see #01163) BCh BYTE AGP MTT Control register (see #01140) BDh BYTE AGP Low Priority Transaction timer register (see #01141) BCh 67 BYTEs reserved
Notes: The 82443EX is virtually identical to the 82443LX, except that it does not support ECC type DRAM.. The Intel 82443EX/LX chipsets use PCI configuration mechanism #1
See Also: #01130 - #01142 - PORT 0CF8h
Format of PCI configuration for Intel 82443EX/LX Device 1 (PCI-PCI): Offset Size Description (Table 01130) 00h 64 BYTEs header, type 1 [bridge] (see #00878) (vendor ID 8086h, device ID 7181h) chipset is 82443EX if revision >= 03h 40h 192 BYTEs reserved
Note: The Intel 82443LX chipset uses PCI configuration mechanism #1
See Also: #01129 - #01143 - PORT 0CF8h
Bitfields for Intel 82443EX/LX (Device 0) PAC Configuration register: Bit(s) Description (Table 01131) 15 WSC# Handshake Disable 14 (82443LX) Host Frequency (read-only). =1 60MHz. =0 66MHz 14 (82443EX) reserved 13-12 reserved 11 ??? (Not documented by Intel!) 10 PCI Agent to Arperture Access Disable 9 Aperture Access Global Enable 8-6 (82443EX) reserved 8-7 (82443LX) DRAM Data Integrety Mode. 00 Non-ECC (no check, no correct). 01 EC-only (do check, no correct). 10 reserved. 11 ECC (do check, do correct) 6 (82443LX) ECC-Test Diagnostic Mode Enabled 5 MDA Present.
Note: Controls routing of Monochrome Display Adaptor I/O and memory range accesses. Works in conjunction with the VGA-bit in Bridge Control register of device 1 (see #00901): VGA MDA 0 0 MDA and VGA routed to PCI bus 0 1 reserved 1 0 MDA and VGA routed to AGP bus 1 1 VGA routed to AGP bus, MDA routed to PCI bus 4-0 reserved
See Also: #00901 - #01129
Bitfields for Intel 82443EX/LX (Device 0) Data Buffer Control register: Bit(s) Description (Table 01132) 7 reserved 6 CPU-to-PCI posting enabled 5 Write post during I/O Bridge access enabled 4-0 reserved
See Also: #01129
Bitfields for Intel 82443EX/LX (Device 0) DRAM Row Type register: Bit(s) Description (Table 01133) 15-14 row 7 type. 0 0 EDO (Same values for each row). 0 1 reserved. 1 0 SDRAM. 1 1 empty row 13-12 row 6 type 11-10 row 5 type 9-8 row 4 type 7-6 row 3 type 5-4 row 2 type 3-2 row 1 type 1-0 row 0 type
See Also: #01129 - #01134
Bitfields for Intel 82443EX/LX (Device 0) DRAM Control register: Bit(s) Description (Table 01134) 7-6 reserved 5 DRAM EDO Auto-Detect mode enabled 4 SDRAM power management enabled 3 reserved 2-0 DRAM Refresh rate. 000 = Refresh disabled. 001 = Normal (Based on PAC Configuration bit 14). 010-111 = reserved
See Also: #01129 - #01133 - #01135
Bitfields for Intel 82443EX/LX (Device 0) DRAM Timing register: Bit(s) Description (Table 01135) 7 SDRAM RAS to CAS Delay (1 = 2 clocks, 0 = 3 clocks) 6 SDRAM CAS Latency (1 = 2 clocks, 0 = 3 clocks) 5 SDRAM RAS Precharge Time (1 = 2 clocks, 0 = 3 clocks) 4 EDO DRAM Read Burst timing. =1 Read rate is x222. =0 Read rate is x333 3 EDO DRAM Write Burst timing. =1 Write rate is x222. =0 write rate is x333 2 EDO RAS Precharge Time (1 = 3 clocks, 0 = 4 clocks) 1 EDO RAS to CAS Delay (1 = 2 clocks, 0 = 3 clocks) 0 MA Wait State. =1 Fast (0 wait states for SDRAM, clocks run normally for EDO). =0 Slow (1 wait state for SDRAM, add one clock to all EDO timings)
See Also: #01129 - #01134
Bitfields for Intel 82443EX/LX DRAM Extended Mode Select register: Bit(s) Description (Table 01136) 15-8 reserved 7-5 Operating Mode. 000 Normal operating mode. 001 NOP command enabled. 010 All banks precharge enable. 011 Mode register set command enable. 100 CBR cycle enable. 101-11x reserved 4 reserved 3-2 Page timeout select. 00 16 clocks. 01-11 reserved 1-0 Close both banks control. 00 close both banks on page misses. 01-11 reserved
See Also: #01129
Bitfields for Intel 82443EX/LX Memory Buffer Strength Control register: Bit(s) Description (Table 01137) 31-30 MAA[1-0] buffer strength. 00 48mA (same values for bits 25-12,5-0). 01 42mA. 10 22mA. 11 reserved 29-28 (82443LX only) MECC[7-0] buffer strength. 00 42mA (same values for bits 27-26,11-6). 01 38mA. 10 33mA. 11 reserved 27-26 MD[63-0] buffer strength 25-24 RCSA[0]# & RCSB[0]#/MAB[6] buffer strength 23-22 (82443LX only) MAB[1-0] buffer strength 21-20 MAA[13:2] buffer strength 19-18 RCSA[1]# & RCSB[1]#/MAB[7] buffer strength 17-16 RCSA[2]# & RCSB[2]#/MAB[8] buffer strength 15-14 RCSA[3]# & RCSB[3]#/MAB[9] buffer strength 13-12 (82443LX only) RCSA[4]# & RCSB[4]#/MAB[10] buffer strength 11-10 (82443LX only) CQDB[5,1]# buffer strength 9-8 CQDA[5,1]# buffer strength 7-6 CQDA[7-6,4-2,0]# buffer strength ---82443LX--- 5-4 RCSA[5]# & RCSB[5]#/MAB[11] buffer strength 3-2 RCSA[6]#/MAB[2] & RCSB[6]#/MAB[12] buffer strength 1-0 RCSA[7]#/MAB[3] & RCSB[7]#/MAB[13] buffer strength ---82443EX--- 5-0 reserved
See Also: #01129
Bitfields for Intel 82443EX/LX Error Status 0 register: Bit(s) Description (Table 01138) ---82443LX--- 7-5 Multi-bit first error (read-only) Indicates which DRAM row had the multi-bit error 4 Multiple-bit ECC Error occurred flag 3-1 Single-bit first row error (read-only) Indicates which DRAM row had the single-bit error 0 Single-bit ECC error occurred flag ---82443EX--- 7-0 reserved
Note: Write a 1 to bits 4 & 0 to clear the flags
See Also: #01129 - #01139
Bitfields for Intel 82443EX/LX Error Status 1 register: Bit(s) Description (Table 01139) 7-3 reserved 2 AGP non-snoopable access outside of graphics arperture 1 AGP non-snoopable access outside of main DRAM ranges and arperture 0 access to invalid graphics arperture translation table entry
Note: Write a 1 to these bit(s) to clear
See Also: #01129 - #01138
Bitfields for Intel 82443EX/LX Multi-Transaction Timer register: Bit(s) Description (Table 01140) 7-3 Multi-transaction timer count value 2-0 reserved
See Also: #01129 - #01141
Bitfields for Intel 82443EX/LX Low Priority Transaction Timer register: Bit(s) Description (Table 01141) 7-3 Low priority transaction timer count value 2-0 reserved
See Also: #01129 - #01140
Format of PCI Configuration for Intel 82443BX Device 0 (Host-PCI): Offset Size Description (Table 01142) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 7190h/7192h) 10h DWORD graphics aperture base address 2Ch WORD subsystem vendor identification (write-once) 2Eh WORD subsystem device identification (write-once) 40h 16 BYTEs reserved (0) 50h DWORD 440BX Configuration (see #01144) 54h 3 BYTEs reserved (0) 57h BYTE DRAM Control (see #01145) 58h BYTE DRAM Timing (see #01146) 59h 7 BYTEs Programmable Attribute Map register 0-6 (see #01118) 60h 8 BYTEs DRAM Row Boundary registers 0-7 each register indicates top of memory for a particular row, in 8MB units; DIMMs use two rows each, with single-sided DIMMs leaving the odd-numbered rows unpopulated 68h BYTE Fixed DRAM Hole Control (see #01147) 69h 6 BYTEs Memory Buffer Strength Control (see #01148) 6Fh 2 BYTEs reserved (0) 71h BYTE Intel Reserved (1Fh) 72h BYTE SMRAM Control (see #01123) 73h BYTE Extended SMRAM Control (see #01149) 74h WORD SDRAM Row Page Size (see #01150) 76h WORD SDRAM Control Register (see #01151) 78h WORD Paging Policy Register (see #01152) 7Ah BYTE Power Management Control (see #01153) 7Bh WORD Suspend CBR Refresh Rate Register (see #01154) 7Dh 3 BYTEs reserved (0) 80h DWORD Error Address Pointer (see #01155) 84h 12 BYTEs reserved (0) 90h BYTE Error Command Register (see #01156) 91h WORD Error Status Register (see #01157) 93h BYTE reserved (0) 94h DWORD Intel Reserved (00006104h) 98h WORD Intel Reserved (0500h) 9Ah BYTE Intel Reserved (0) 9Bh 5 BYTEs reserved (0) A0h DWORD AGP Capability Identifier (see #01158) A4h DWORD AGP Status Register (read-only) (see #01159) A8h DWORD AGP Command Register (see #01160) ACh 4 BYTEs reserved (0) B0h DWORD AGP Control Register (see #01161) B4h BYTE Aperture Size Control (see #01162) B5h 3 BYTEs reserved (0) B8h DWORD Aperture Translation Table (see #01163) BCh 2 BYTEs reserved BEh WORD reserved (0) C0h DWORD Intel Reserved (0) C4h DWORD Intel Reserved (0) C8h BYTE Intel Reserved (18h) C9h BYTE Intel Reserved (0Ch) CAh 3 BYTEs Memory Buffer Frequency Select (see #01164) CDh 3 BYTEs reserved (0) D0h 8 BYTEs BIOS scratch pad (read-write, init to 0 on reset) D8h 8 BYTEs Intel Reserved (0) E0h 2 DWORDs DRAM Write Thermal Throttling Control (see #01165) E8h 8 BYTEs DRAM Read Therman Throttling Control (see #01165) F0h WORD Buffer Control Register (see #01166) F2h 2 BYTEs Intel Reserved (0000h) F4h DWORD Intel Reserved (0000F800h) bits 30-29 are "Abort Disable Test Mode" configuration bits and should always be set (according to Intel Specification Update) F8h DWORD Intel Reserved (00000F20h) FCh DWORD Intel Reserved (0)
See Also: #00873 - #01143 - PORT 0022h"82443BX" !!!intel\29063301.pdf p.34
Format of PCI Configuration for Intel 82443BX Device 1 (PCI-AGP): Offset Size Description (Table 01143) 00h 64 BYTEs header, type 1 [bridge] (see #00878) (vendor ID 8086h, device ID 7191h) 40h 192 BYTEs reserved
See Also: #00873 - #01142 - #01130 !!!intel\29063301.pdf p.80
Bitfields for Intel 82443BX (Device 0) NBX Configuration Register: Bit(s) Description (Table 01144) 31-24 SDRAM rows without ECC; each set bit indicates a row in the SDRAM array with does NOT have error correction (bit 24 = row 0; note that double- sided DIMMs use two rows, one for the front and one for the back) 23-19 reserved 18 DRAM data asserted on host bus on the same clock on which the snoop result is sampled, instead of one clock later 17 ECC signals are always driven for EDO memory 16 IDSEL redirection. =0 allocate IDSEL1/AD12 to bridge, never assert external AD12. =1 allocate IDSEL7/AD18 to bridge, never assert external AD18; PCI configuration cycles for Bus0/Device7 are redirected to Bus0/Device1 15 disable WSC# handshake (uni-processor mode) 14 Intel Reserved 13:12 Host/DRAM frequency. 00 100 MHz. 01 reserved. 10 66 MHz. 11 reserved
11 enable AGP-to-PCI access (note:
AGP-to-PCI traffic is not allowed to target ISA-bus devices) 10 disable PCI agent access to graphis aperture (ignored if bit 9 clear) 9 global enable graphics aperture access 8:7 DRAM Data Integrity Mode. 00 non-ECC. 01 error checking only (e.g. parity). 10 ECC mode. 11 ECC mdoe with hardware scrubbing 6 enable ECC diagnostics mode (when set, ECC lines are forced to zero on writes and compared to internally-generated ECC on reads) 5 monochrome video adapter present on PCI/ISA bus (with primary adapter on AGP bus). If register 3Eh bit 3 is clear, all VGA cycles are sent to PCI regardless of this bit.Otherwise:
If clear, all VGA cycles are sent to AGP; if set, all VGA cycles except MDA ranges (memory B0000h-B7FFFh and ports 03B4h,03B5h, 03B8h,03B9h,03BAh,03BFh) are sent to AGP 4 reserved 3 enable posting of host USWC (U??? Speculative Write Combine) writes to PCI memory 2 In-Order Queue Depth. =1 maximum (PPro supports up to 8, but 82443BX only supports depth 4). =0 depth forced to 1 (no pipelining on processor bus) 1:0 reserved
See Also: #01142
Bitfields for 82443BX DRAM Control: Bit(s) Description (Table 01145) 7-6 reserved 5 module mode configuration (read-only). =0 self-refresh entry is staggered; if "SDRAMPWR" (offset 76h bit 4) is set, 3 DIMMs are supported, CKE[5:0] is driven, and dynamic SDRAM power-down is available; if "SDRAMPWR" is clear, 4 DIMMs are supported but power-down is not available. =1 self-refresh entry is not staggered; 3 DIMMs are supported, only CKE0 is driven, and dynamic power-down is not available 4:3 DRAM type. 00 EDO. 01 SDRAM. 10 registered SDRAM. 11 reserved 2:0 DRAM refresh rate. 000 disabled. 001 15.6 microseconds. 010 31.2 microseconds. 011 62.4. 100 124.8. 101 249.6. Else reserved
See Also: #01142
Bitfields for Intel 82443BX DRAM Timing: Bit(s) Description (Table 01146) 7-2 reserved 1 add one EDO RASx# wait state for row misses (two tASR instead of one) 0 add one wait state to first EDO CASx# assertion for page hits. (2 Tasc instead of 1 Tasc)
See Also: #01142
Bitfields for Intel 82443BX/EX/LX Fixed DRAM Hole Control: Bit(s) Description (Table 01147) 7-6 Hole Enable. 00 none. 01 512K-640K. 10 15M-16M. 11 reserved 5-0 reserved (0)
See Also: #01142 - #01129
Bitfields for Intel 82443BX Memory Buffer Strength Control: Bit(s) Description (Table 01148) 47-40 reserved (0) 39-38 strengths of MAA[13:0], WEA#, SRASA#, SCASA# (settings same as below) 37-36 strengths of MAB[12:11,9:0], MAB[13,10], WEB#, SRASB#, SCASB#. 00 = 1x (at both 66 and 100 MHz). 01 reserved. 10 = 2x (at both 66 and 100 MHz). 11 = 3x (at both 66 and 100 MHz) 35-34 MD[63:0] buffer strength control 2.
4 DIMM FET config:
Strength for MD[63:0] path connected to DIMMs 2&3.3/4 DIMM non-FET config:
Program to same value as buffer str. ctrl 1 33-32 MD[63:0] buffer strength control 1.4 DIMM FET config:
Strength for MD[63:0] path connected to DIMMs 0&1.3/4 DIMM non-FET config:
Programmable based on total load detected on all DIMM connectors. 00 = 1x (at both 66 and 100 MHz). 01 reserved. 10 = 2x (at both 66 and 100 MHz). 11 = 3x (at 100 MHz only) 31-30 MECC[7:0] buffer strength control 2.4 DIMM FET config:
Strength for MECC[7:0] path connected to DIMMs 2&3.3/4 DIMM non-FET config:
Program to same value as buffer str. ctrl 1 29-28 MECC[7:0] buffer strength control 1.4 DIMM FET config:
Strength for MD[63:0] path connected to DIMMs 0&1.3/4 DIMM non-FET config:
Programmable based on total load detected on all DIMM connectors. (values same as for MD[63:0] buffer strength) 27-26 CSB7#/CKE5 buffer strength (same values as bits 37-36) 25-24 CSA7#/CKE3 buffer strength (same values as bits 37-36) 23-22 CSB6#/CKE4 buffer strength (same values as bits 37-36) 21-20 CSA6#/CKE2 buffer strength (same values as bits 37-36) 19 CSA5#/RASA5#, CSB5#/RASB5# buffer strength. 0 = 1x (at both 66 and 100 MHz). 1 = 2x (at both 66 and 100 MHz) 18 CSA4#/RASA4#, CSB4#/RASB4# buffer strength (same values as bit 19) 17 CSA3#/RASA3#, CSB3#/RASB3# buffer strength (same values as bit 19) 16 CSA2#/RASA2#, CSB2#/RASB2# buffer strength (same values as bit 19) 15 CSA1#/RASA1#, CSB1#/RASB1# buffer strength (same values as bit 19) 14 CSA0#/RASA0#, CSB0#/RASB0# buffer strength (same values as bit 19) 13-12 DQMA5/CASA5# buffer strength. 00 = 1x (at both 66 and 100 MHz). 01 reserved. 10 = 2x (at both 66 and 100 MHz). 11 = 3x (at 66 MHz only) 11-10 DQMA1/CASA1# buffer strength (same values as bits 37-36) 9-8 DQMB5/CASB5# buffer strength (same values as bits 13-12) 7-6 DQMB1/CASB1# buffer strength (same values as bits 13-12) 5-4 DQMA[7:6,4:2,0]/CASA[7:6,4:2,0]# buffer strength (as for bits 37-36) 3-2 CKE1/GCKE buffer strength (same values as bits 37-36) 1-0 CKE0/FENA buffer strength (same values as bits 37-36)
See Also: #01142
Bitfields for Intel 82439TX/82443BX Extended SMRAM Control register: Bit(s) Description (Table 01149) 7 SMRAM location. =0 compatible SMRAM space at segment A000h. =1 high SMRAM space at addreses 100A0000h to 100FFFFFh (accessing physical DRAM addresses A0000h to FFFFFh) 6 (write-clear) access to extended SMRAM memory range when SMRAM space is not open and not in SMM 5 enable write-through caching of SMRAM. (forced to 1 by 82443BX, to 0 by 82439TX) 4 enable L1 caching of SMRAM (forced to 1 by 82443BX) 3 enable L2 caching of SMRAM (forced to 1 by 82443BX) 2-1 TSEG size (read-only once SMRAM locked) (see #01123). 00 128K. 01 256K. 10 512K. 11 1M 0 enable TSEG (read-only once SMRAM locked) (see #01123). When both SMRAM and TSEG are enabled, the top N kilobytes of physical DRAM are no longer claimed by the memory controller, and instead appear as extended SMRAM at an address 256M higher than the physical address
See Also: #01142 - #01123 - #01099
Bitfields for Intel 82443BX SDRAM Row Page Size: Bit(s) Description (Table 01150) 15-14 page size for row 7 (back of DIMM4). 00 two KB. 01 four KB. 10 eight KB. 11 reserved 13-12 page size for row 6 (front of DIMM4) ... 3-2 page size for row 1 (back of DIMM1) 1-0 page size for row 0 (front of DIMM1)
See Also: #01142
Bitfields for Intel 82443BX SDRAM Control Register: Bit(s) Description (Table 01151) 15-10 reserved (0) 9-8 add one-clock delay to idle/pipeline DRAM leadoff when =01 (all other values are illegal) 7-5 SDRAM mode select. 000 normal operation. 001 issue NOP command on all CPU-to-SDRAM cycles. 010 issue All-Banks-Precharge command on all CPU-to-SDRAM cycles. 011 issue mode register set command on CPU-to-SDRAM cycles (command is driven on memory address lines, so the proper address must be calculated for each row of memory to drive the correct command; MAx[2:0] must be driven to 010 for burst-of-4 mode, MAx3 to 1 for interleave wrap type, MAx4 to the value of the CAS# latency bit, MAx[6:5] to 01, and MAx[12:7] to 0000000. 100 issue CBR cycles on all CPU-to-SDRAM cycles. Else reserved 4 "SDRAMPWR" specifies how CKE signals are driven for various DRAM configurations; refer to #01145 bit 5 3 Leadoff Command Timing. =0 four CS# clocks (100 MHz or 66 MHz desktop if MAA/MAB load > 9). =1 three CS# clocks (66 MHz mobile platforms, or desktop w/ load <= 9) 2 CAS# latency. =0 three DCLKs. =1 two DCLKs 1 SDRAM RAS# to CAS# delay. =0 three clocks. =1 two clocks 0 SDRAM RAS# precharge. =0 three clocks. =1 two clocks
See Also: #01142
Bitfields for Intel 82443BX Paging Policy Register: Bit(s) Description (Table 01152) 15-8 banks per row (bit 7 is row 0, bit 15 is row 7). =0 two banks. =1 four banks 7-5 reserved 4 Intel Reserved 3-0 DRAM Idle Timer ("DIT"). Number of clocks in idle state before all pages are precharged. 0000 no clocks. 0001 2 clocks. 0010 4 clocks. 0011 8 clocks. 0100 10 clocks. 0101 12 clocks. 0110 16 clocks. 0111 32 clocks. 1xxx never (pages are not closed on idle)
See Also: #01142
Bitfields for Intel 82443BX Power Management Control Register: Bit(s) Description (Table 01153) 7 enable SDRAM power-down for idle rows 6 enable ACPI control register at PORT 0022h 5 suspend refresh type. =0 self-refresh. =1 CBR mode 4 enable normal refresh (must be set before accessing RAM after a reset) 3 quick-start mode enabled (read-only) 2 enable dynamic clock gating on AGPset "IDLE" condition (all buses in idle state) 1 AGP disabled (read-only) 0 enable CPU reset without PCIRST enable
See Also: #01142
Bitfields for Intel 82443BX Suspend CBR Refresh Rate: Bit(s) Description (Table 01154) 15-13 reserved (0) 12 enable automatic Suspend CBR Refresh Rate adjustment (based on number of OSCCLKs in a given time); if clear, the below field must be programmed to guarantee minimum refresh rates in the worst case 11-0 Suspend CBR Refresh Rate (number of OSCCLKs between refresh requests)
See Also: #01142
Bitfields for Intel 82443BX Error Address Pointer: Bit(s) Description (Table 01155) 31-12 (read-only) bits 31-12 of address in which first parity/ECC error occurred 11-2 reserved 1 (write-clear) multi-bit error occurred 0 (write-clear) single-bit error occurred
See Also: #01156 - #01142
Bitfields for Intel 82443BX/EX/LX Error Command Register: Bit(s) Description (Table 01156) 7 enable SERR# on AGP non-snoopable access outside graphics aperture 6 enable SERR# on invalid AGP DRAM access (82443BX). Enable SERR# on AGP Non-snoopable access to location outside main DRAM and arpeture rangles (82443EX/LX) 5 enable SERR# on access to invalid Graphics Aperture Translation Table 4 enable SERR# on receiving Target Abort 3 enable SERR# when Thermal DRAM Throttling detected (82443BX). Enable SERR# on PCI Parity Error (82443EX/LX) ---82443BX--- 2 SERR# mode. =0 asserted for one PCI clock. =1 level mode signal (for systems that connect SERR# to EXTSMI#) 1 enable SERR# on receiving multi-bit Parity/ECC error 0 enable SERR# on receiving single-bit (corrected) ECC error ---82443EX/LX--- 2-0 reserved
Note: Bits 1 and 0 must be clear on systems not supporting ECC
See Also: #01155 - #01157 - #01142 - #01129
Bitfields for Intel 82443BX Error Status Register: Bit(s) Description (Table 01157) 15-13 reserved (0) 12 (write-clear) DRAM Read thermal throttling condition occurred 11 (write-clear) DRAM Write thermal throttling condition occurred 10 (write-clear) AGP non-snoopable access outside Graphics Aperture 9 (write-clear) invalid AGP non-snoopable DRAM read access 8 (write-clear) invalid Graphics Aperture Translation Table entry 7-5 (read-only) number of DRAM row containing first multi-bit error 4 (write-clear) multi-bit (uncorrectable) error occurred 3-1 (read-only) number of DRAM row containing first single-bit error 0 (write-clear) single-bit (correctable) error occurred
See Also: #01156 - #01142
Bitfields for Intel AGP Capability Identifier: Bit(s) Description (Table 01158) 31-24 reserved 23-20 major version of supported AGP revision 19-16 minor version of supported AGP revision 15-8 offset of next capability (0 = none) 7-0 PCI capability ID (2 = AGP, 0 = disabled)
See Also: #01142 - #01159 - #01129
Bitfields for Intel 82443BX/EX/LX AGP Status Register: Bit(s) Description (Table 01159) 31-24 maximum AGP request queue depth (read-only) 23-10 reserved 9 AGP side band addressing is supported (read-only) 8-2 reserved 1-0 supported AGP data transfer type(s).
Bit 0:
1x data transfer mode.Bit 1:
2x data transfer mode
Note: Bits 0 and 1 may not both be clear
See Also: #01160 - #01142 - #01158 - #01129
Bitfields for Intel 82443BX/EX/LX AGP Command Register: Bit(s) Description (Table 01160) 31-10 reserved 9 enable AGP sideband addressing 8 enable AGP 7-2 reserved 1-0 selected AGP transfer rate. 00 = default. 01 = 1x. 10 = 2x. 11 illegal
See Also: #01159 - #01142 - #01161 - #01129
Bitfields for Intel 82443BX/EX/LX AGP Control Register: Bit(s) Description (Table 01161) 31-16 reserved (0) 15 disable forced ordering of snoopable writes and AGP reads (82443BX). (82443EX/LX) reserved 14 reserved (0) 13 enable Graphics Aperture Write-AGP Read synchronization 12-10 reserved (0) 9-8 reserved (0) (82443BX). Expedite transaction throttle timer (82443EX/LX). 00 no throttling. 01 reserved. 10 192 clocks on, 64 clocks off. 11 reserved 7 enable Graphics Translation Lookaside Buffer (and GTLB Flush Control) 6-0 reserved (0)
See Also: #01160 - #01142 - #01129
Bitfields for Intel 82443BX/EX/LX Graphics Aperture Size Control: Bit(s) Description (Table 01162) 7-6 reserved 5-0 aperture size. 000000 256M. 100000 128M. 110000 64M. 111000 32M. 111100 16M. 111110 8M. 111111 4M. Other illegal
See Also: #01142 - #01163 - #01129
Bitfields for Intel 82443BX/EX/LX Graphics Aperture Trans. Table Base Register: Bit(s) Description (Table 01163) 31-12 bits 31-12 of aperture translation table base address 11-0 reserved (0)
See Also: #01162 - #01142 - #01129
Bitfields for Intel 82443BX Memory Buffer Frequency Select: Bit(s) Description (Table 01164) 23 reserved 22 MAA[13:0], WEA#, SRASA#, SCASA# buffer select. =0 66 MHz buffers. =1 100 MHz buffers 21 MAB[12:11,9:0]#, MAB[13,10], WEB#, SRASB#, SCASB# buffer select. (as for bit 22) 20 MD[63:0] (control 2) buffer select 19 MD[63:0] (control 1) buffer select 18 MECC[7:0] (control 2) buffer select 17 MECC[7:0] (control 1) buffer select 16 CSB7#/CKE5 buffer select 15 CSA7#/CKE3 buffer select 14 CSB6#/CKE4 buffer select 13 CSA6#/CKE2 buffer select 12 CSA5#/RASA5#, CSB5#/RASB5# buffer select 11 CSA4#/RASA4#, CSB4#/RASB4# buffer select 10 CSA3#/RASA3#, CSB3#/RASB3# buffer select 9 CSA2#/RASA2#, CSB2#/RASB2# buffer select 8 CAS1#/RASA1#, CSB1#/RASB1# buffer select 7 CSA0#/RASA0#, CSB0#/RASB0# buffer select 6 DQMA5/CASA5# buffer select 5 DQMA1/CASA1# buffer select 4 DQMB5/CASB5# buffer select 3 DQMB1/CASB1# buffer select 2 DQMA[7:6,4:2,0]/CASA[7:6,4:2,0]# buffer select 1 CKE1/GCKE buffer select 0 CKE0/FENA buffer select
See Also: #01142 - #01166
Bitfields for Intel 82443BX DRAM Read/Write Thermal Throttling Control: Bit(s) Description (Table 01165) 63 lock all read and write throttle control register bits (exists in Write Throttling control register only) 62-46 reserved 45-38 global DRAM sampling window (in four-millisecond units) 37-26 global QWORD threshold (documented as units of 215, but may be typo and actually be units of 2^15 = 32768). Thermal throttling will be invoked if the number of QWORD accesses during the sampling window exceeds the threshold count 25-20 throttle time in multiples of the sampling window 19-13 throttle monitoring window in 16 DRAM-clock units 12-3 throttle QWORD maximum count -- while throttling is enabled, at most this many QWORD accesses are permitted during each throttle monitoring window 2-0 DRAM Throttle Mode. 100 normal operation. Else Intel Reserved
See Also: #01142
Bitfields for Intel 82443BX Buffer Control Register: Bit(s) Description (Table 01166) 15-10 reserved 9-6 AGP Jam Latch strength.
Bit 9:
Enable strong pull-up.Bit 8:
Enable weak pull-up.Bit 7:
Enable strong pull-down.Bit 6:
Enable weak pull-down 5-0 Intel Reserved
See Also: #01142 - #01164
Format of PCI Configuration for Intel 82371FB/82371SB Function 0 (ISA Bridge): Offset Size Description (Table 01167) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 122Eh/7000h) (revision ID 00h = 82371SB step A-1) (revision ID 01h = 82371SB step B-0) 40h 12 BYTEs reserved 4Ch BYTE ISA I/O Controller Recovery Timer (see #01087) 4Dh BYTE reserved 4Eh BYTE X-Bus Chip Select Enable (see #01089) 4Fh BYTE (82371SB) X-Bus Chip Select Enable High (see #01102)
bit 0:
I/O APIC enabled 4Fh BYTE (82371FB) reserved 50h 16 BYTEs reserved 60h 4 BYTEs PCI IRQ Route Control (see #01076) 64h 5 BYTEs reserved 69h BYTE top of memory (see #01216) 6Ah WORD miscellaneous status (see #01217) 6Ch 4 BYTEs reserved 70h BYTE motherboard IRQ Route Control 0 (see #01218) 71h BYTE (82371FB) motherboard IRQ Route Control 1 (see #01218) 72h 4 BYTEs reserved 76h 2 BYTEs motherboard DMA control (see #01219) 78h WORD programmable chip select control (see #01220) 7Ah 6 BYTEs reserved 80h BYTE (82371SB) APIC Base Address Relocation (see #01078) 81h BYTE reserved 82h BYTE (82371SB) Deterministic Latency Control (see #01221) 83h 29 BYTEs reserved A0h BYTE SMI Control (see #01222) A1h BYTE reserved A2h WORD SMI Enable (see #01080) A4h DWORD System Event Enable (SEE) (see #01081) A8h BYTE Fast-Off Timer (in minutes, PCICLKs, or milliseconds) value is count less one; timer must be stopped before changing its value A9h BYTE reserved AAh WORD SMI Request (see #01082) ACh BYTE Clock Scale STPCLK# Low Timer STPCLK# stays low for 1+1056*(value+1) PCICLKs ADh BYTE reserved AEh BYTE Clock Scale STPCLK# High Timer STPCLK# stays high for 1+1056*(value+1) PCICLKs AFh 81 BYTEs reserved
See Also: #00873 - #01214 - #01215 - #01064 - #01083 - #01108 - #01098
Format of PCI configuration for Intel 82371MX MPIIX: Offset Size Description (Table 01168) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 1234h) 40h 9 BYTEs reserved 49h BYTE serial and parallel port enable (see #01169) 4Ah 2 BYTEs reserved 4Ch BYTE Extended I/O Controller Recovery Timer (see #01170) 4Dh BYTE reserved 4Eh BYTE BIOS enable (see #01171) 4Fh BYTE FDC enable (see #01172) 50h 16 BYTEs reserved 60h BYTE PIRQA# Route Control (see #01076) 61h BYTE PIRQB# Route Control (see #01076) 62h 8 BYTEs reserved 6Ah WORD Miscellaneous Status (see #01173) 6Ch WORD IDE timing modes (see #01223) 6Eh 2 BYTEs reserved 70h BYTE Motherboard IRQ Route Control (see #01223) 71h 5 BYTEs reserved 76h 3 BYTEs Motherboard DMA Route Control (see #01219) 79h 5 BYTEs reserved 7Eh BYTE Audio enable (see #01174) 7Fh BYTE DMA channel 5-7 address size (see #01175) 80h BYTE PCI DMA enable (see #01176) 81h 7 BYTEs reserved 88h BYTE PCI DMA/PCI DMA expansion A (see #01177) 89h BYTE PCI DMA/PCI DMA expansion B (see #01177) 8Ah WORD Programmable Memory Address Control 0 (see #01178) 8Ch WORD Programmable Memory Address Control 1 (see #01178) 8Eh WORD Programmable Memory Address Mask (see #01179) 90h BYTE Programmable Address Range Enable (see #01180) 91h BYTE reserved 92h WORD Programmable Chip Select Control (see #01181) 94h WORD Programmable Address Control 1 (see #01182) 96h WORD Programmable Address Control 2 (see #01182) 98h WORD Programmable Address Control 3 (see #01182) 9Ah BYTE Programmable Address Mask A (see #01183) 9Bh BYTE Programmable Address Mask B (see #01184) 9Ch WORD I/O configuration address (see #01185) 9Eh 2 BYTEs reserved A0h WORD Programmable Address Control 4 (see #01182) A2h WORD Programmable Address Control 5 (see #01182) A4h BYTE Programmable Address Mask C (see #01186) A5h BYTE Peripheral Access Detect Enable 0 (see #01187) A6h BYTE Peripheral Access Detect Enable 1 (see #01188) A7h BYTE Peripheral Access Detect Enable 2 (see #01189) A8h WORD Local Trap Address for Device 3 (see #01190) AAh BYTE Local Trap Mask for Device 3 (see #01191) ABh BYTE Local Trap SMI Enable (see #01192) ACh 2 BYTEs reserved AEh BYTE Local Trap SMI Status (see #01192) AFh BYTE reserved B0h BYTE Local Standby SMI Enable (see #01193) B1h BYTE Local Standby Timer Reload Enable (see #01194) B2h BYTE Local Standby SMI Status (see #01193) B3h BYTE reserved B4h BYTE Local Standby Timer IDE Idle (see #01195) B5h BYTE Local Standby Timer Audio Idle (see #01195) B6h BYTE Local Standby Timer COM Idle (see #01195) B7h BYTE reserved B8h BYTE Local Standby Timer Device 1 Idle (see #01195) B9h BYTE Local Standby Timer Device 2 Idle (see #01195) BAh BYTE Local Standby Timer Device 3 Idle (see #01195) BBh BYTE reserved BCh BYTE Software/EXTSMI# SMI Delay Timer (see #01195) BDh BYTE Suspend SMI Delay Timer (see #01195) BEh BYTE Global Standby Timer (see #01195) BFh BYTE Clock Throttle Standby Timer (see #01195) C0h BYTE System Management Control (see #01196) C1h BYTE System SMI Enable (see #01197) C2h BYTE Miscellaneous SMI Enable (see #01198) C3h BYTE Global SMI Enable (see #01200) C4h 2 BYTEs reserved C6h BYTE System SMI Status (see #01197) C7h BYTE Miscellaneous SMI Status (see #01199) C8h BYTE Global SMI Status (see #01201) C9h 3 BYTEs reserved CCh BYTE Suspend/Resume Control 1 (see #01202) CDh BYTE Suspend/Resume Control 2 (see #01203) CEh BYTE SMOUT Control (see #01204) CFh BYTE reserved D0h BYTE System Event Enable 0 (see #01207) D1h BYTE System Event Enable 1 (see #01208) D2h BYTE System Event Enable 2 (see #01209) D3h BYTE Burst Count Timer (see #01195) D4h BYTE Clock Control (see #01205) D5h BYTE reserved D6h BYTE STPCLK# Low Timer (see #01195) D7h BYTE STPCLK# High Timer (see #01195) D8h BYTE Stop Break Event Enable 0 (see #01207) D9h BYTE Stop Break Event Enable 1 (see #01208) DAh BYTE Stop Break Event Enable 2 (see #01209) DBh 5 BYTEs reserved E0h BYTE Shadow Register (see #01206) E1h 3 BYTEs reserved E4h BYTE Burst Clock Event Enable 0 (see #01207) E5h BYTE Burst Clock Event Enable 1 (see #01208) E6h BYTE Burst Clock Event Enable 2 (see #01209) E7h BYTE Burst Clock Event Enable 3 (see #01210) E8h BYTE Burst Clock Event Enable 4 (see #01211) E9h BYTE Burst Clock Event Enable 5 (see #01212) EAh BYTE Burst Clock Event Enable 6 (see #01213) EBh BYTE reserved ECH BYTE Clock Throttle Break Event Enable 0 (see #01207) EDh BYTE Clock Throttle Break Event Enable 1 (see #01208) EEh BYTE Clock Throttle Break Event Enable 2 (see #01209) EFh BYTE Clock Throttle Break Event Enable 3 (see #01210) F0h BYTE Clock Throttle Break Event Enable 4 (see #01211) F1h BYTE Clock Throttle Break Event Enable 5 (see #01212) F2h BYTE Clock Throttle Break Event Enable 6 (see #01213) F3h 13 BYTES reserved
See Also: #00873 - #01076
Bitfields for Intel 82371MX serial and parallel port enable register: Bit(s) Description (Table 01169) 7 reserved 6 LPT3 enabled 5 LPT2 enabled 4 LPT1 enabled 3 COM4 enabled 2 COM3 enabled 1 COM2 enabled 0 COM1 enabled
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Extended I/O Controller Recovery Timer register: Bit(s) Description (Table 01170) 7 reserved 6 8-Bit I/O Recovery Enable. =1 Enable value programmed into bits 5-3 5-3 8-Bit I/O Recovery Times. 000 = 8 SYSCLK. 001 = 1 SYSCLK (default). 010 = 2 SYSCLK. 011 = 3 SYSCLK. 100 = 4 SYSCLK. 101 = 5 SYSCLK. 110 = 6 SYSCLK. 111 = 7 SYSCLK 2-0 Reserved (0)
See Also: #01168 - #01087 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX BIOS enable register: Bit(s) Description (Table 01171) 7 Extended BIOS Enable 6 Lower BIOS Enable 1 5 Lower BIOS Enable 0 4 Lower BIOS CS# Enable 0 3 F Segment BIOS Enable 2 BIOSCS# Write Protect 1-0 reserved
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX FDC Enable register: Bit(s) Description (Table 01172) 7 Coprocessor Error fuction Enable 6 IRQ12/M Mouse Function Enable 5 System Management Output 5/Disk Output Enable 4 System Management Output 4/RTCALE Enable 3 Motherboad DMA 2 Disable 2 reserved 1 Floppy Secondary Addess Enable 0 Floppy Primary Address Enable
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Miscellaneous Status register: Bit(s) Description (Table 01173) 15-3 reserved 2-1 reserved (0) 0 ISA Clock Divisor Status. =1 Divisor=3 (PCICLK=25MHz) default. =0 Divisor=4 (PCICLK=33MHz)
Note: This is a read-only register that reports on chipset jumper settings.
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Audio enable register: Bit(s) Description (Table 01174) 7 Audio enabled 6-4 Reserved 3-2 Audio I/O Address. 00 0220h. 01 0230h. 10 0240h. 11 0250h 1-0 reserved
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX DMA channel 5-7 address size register: Bit(s) Description (Table 01175) 7 Channel 7 16/8-Bit Count by Word/Byte. =1 16-bit, count by word. =0 8-bit, count by byte 6 Channel 6 16/8-Bit Count by Word/Byte (same values as bit 7) 5 Channel 5 16/8-Bit Count by Word/Byte (same values as bit 7) 4-3 reserved (0)
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX PCI DMA Enable register: Bit(s) Description (Table 01176) 7 DMA CH7 is on PCI Bus 6 DMA CH6 is on PCI Bus 5 DMA CH5 is on PCI Bus 4 reserved 3 DMA CH3 is on PCI Bus 2 DMA CH2 is on PCI Bus 1 DMA CH1 is on PCI Bus 0 DMA CH0 is on PCI Bus
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX PCI DMA/PCI DMA expansion registers: Bit(s) Description (Table 01177) 7-4 reserved 3 Expansion enabled 2-0 DMA channel
Note: The PCI DMA Expansion request lines (REQ[A,B]#/GNT[A,B]#) provide PCI DMA and PCI DMA expansion support.
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Programmable Memory Address Control registers: Bit(s) Description (Table 01178) 15-0 Memory Access Control
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Programmable Memory Address Mask register: Bit(s) Description (Table 01179) 7-0 Memory Address Mask
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Programmable Address Range Enable register: Bit(s) Description (Table 01180) 7 PCS# Enabled for Programmable Address Range 2 6 PCS# Enabled for Programmable Address Range 1 5 Programmable Address range 5 Enabled 4 Programmable Address range 4 Enabled 3 Programmable Address range 5 Enabled 2 Programmable Address range 3 Enabled 1 Programmable Address range 1 Enabled 5 PCS# Address range Enabled
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Programmable Chip Select Control register: Bit(s) Description (Table 01181) 15-0 PCS# Address
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Programmable Address Control registers: Bit(s) Description (Table 01182) 15-0 Programmable Address Control
Note: This register selects a 16-bit I/O address range to be forwarded to the Extended I/O Bus, if enabled in the Programmable Address Range register.
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Programmable Address Mask A register: Bit(s) Description (Table 01183) 7-4 Programmable Address Control 1 Mask 3-0 Programmable Chip Select Mask
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Programmable Address Mask B register: Bit(s) Description (Table 01184) 7-4 Programmable Address Control 3 Mask 3-0 Programmable Address Control 2 Mask
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX I/O configuration address register: Bit(s) Description (Table 01185) 15-10 reserved 9-1 I/O Configuration Address 0 I/O Configuration Address Enabled
Note: This register provides an I/O address range to be forwarded to the Extended I/O Bus for accesses to the configuration space of an integrated I/O device. PCI address bits 9-1 are compared to bits 9-1 of this register. Address bits 31-10 must be 0.
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Programmable Address Mask C register: Bit(s) Description (Table 01186) 7-4 Programmable Address Control 5 Mask 3-0 Programmable Address Control 4 Mask
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Peripheral Access Detect Enable 0 register: Bit(s) Description (Table 01187) 7 Enable Audio-E 6 Enable Audio-D 5 Enable Audio-C 4 Enable Audio-B 3 Enable Audio-A 2 Enable Parallel 3 1 Enable Parallel 2 0 Enable Parallel 1
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Peripheral Access Detect Enable 1 register: Bit(s) Description (Table 01188) 7 Enable COM4 6 Enable COM3 5 Enable COM3 4 Enable COM1 3 Enable Secondary FDC 2 Enable Primary FDC 1 Enable Secondary IDE 0 Enable Promary IDE
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Peripheral Access Detect Enable 2 register: Bit(s) Description (Table 01189) 7 Enable PMAC1 6 Enable PMAC0 5 Enable PAC5 4 Enable PAC4 3 Enable PAC3 2 Enable PAC2 1 Enable PAC1 0 Enable PCSC
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Local Trap Address for Device 3 register: Bit(s) Description (Table 01190) 15-0 Local Trap Address base for Device 3
Note: Is compared with bits 15-0 of PCI I/O Addresses. Address bits 31-16 must be 0.
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Local Trap Mask for Device 3 register: Bit(s) Description (Table 01191) 7-4 Local Trap COM Port Select. =1000 COM4 02E8h-02EFh. =0100 COM3 03E8h-83EFh. =0010 COM2 02F8h-02FFh. =0001 COM1 03F8h-03FFh
Note: These bits when set cause an SMI# when access to the corresponding I/O port range is made. 3-0 Local Trap Mask
Note: This field selects the range of trappable addresses (in bytes).
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Local Trap SMI Enable/Status registers: Bit(s) Description (Table 01192) 7-6 reserved 5 IDE 4 Audio 3 COM 2 DEV3 1 DEV2 0 DEV1
Note: A set bit indicates in the Enable register turns generation of SMI# on I/O accesses to the address region used by the selected device; a set bit in the Status register indicates which trap caused an SMI# interrupt.
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Local Standby SMI Enable/Status registers: Bit(s) Description (Table 01193) 7-6 reserved 5 IDE 4 Audio 3 COM 2 DEV3 1 DEV2 0 DEV1
Note: Each bit in the Enable register turns on the associated SMI Timer; a set bit in the Status register indicates which local standby timer caused the SMI interrupt
See Also: #01168 - #01194 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Local Standby Timer Reload Enable register: Bit(s) Description (Table 01194) 7 IDE 6 Audio 5 COM 4 DEV3 3 DEV2 2 DEV1 1 Audio MDAK2 0 Audio MDAK1
Note: This register enables local standby timer reloading. When the associated I/O address range is accessed, the standby timer is reloaded with it's default value. Also note the different bit-order for this register only.
See Also: #01168 - #01193 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Count Value registers: Bit(s) Description (Table 01195) 7-0 Count value
Note: This field contains the initial count value for various time-out events. 00 is an illegal programmed value. The programmed value is decremented by certain events or system clocks, and the event is triggered when the count reaches 0.
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX System Management Control register: Bit(s) Description (Table 01196) 7-3 reserved 2 Freeze (but not reset) all Power Management timers 1 =0 disable all Power Management functions 0 =0 disable SMI
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX System SMI Enable/Status registers: Bit(s) Description (Table 01197) 7 reserved 6 Write to APMC Port (software SMI) 5 EXTSMI# 4 IRQ12 3 IRQ8 2 IRQ4 1 IRQ3 0 IRQ1
Note: Each set bit in the Enable register turns on SMI# generation for the associated hardware event; a set bit in the Status register indicates which event caused the SMI interrupt
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Miscellaneous SMI Enable register: Bit(s) Description (Table 01198) 7-4 reserved 3 Write to APMC Port 2 SRBTN# 1 BATLOW# 0 reserved
Note: Enables SMI# generation for the above hardware events
See Also: #01168 - #01199 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Miscellaneous SMI Status register: Bit(s) Description (Table 01199) 7-4 reserved 3 =1 indicates system is in global standby mode 2 SRBTN# caused SMI 1 BATLOW# caused SMI 0 reserved
See Also: #01168 - #01198 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Global SMI Enable register: Bit(s) Description (Table 01200) 7 System Events Enabled 6 Software SMI#'s (generated by bit 0 of this register) Enabled 5 reserved 4 Local Traps Enabled 3 Local Standby Timers Enabled 2 Global Standby Timer Enabled 1 SRBTN# and BATLOW# Enabled
Note: Enables SMI# generation for the above hardware events
See Also: #01168 - #01201 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Global SMI Status register: Bit(s) Description (Table 01201) 7 One of the System Events caused SMI 6 Software SMI or EXTSMI# caused SMI 5 Write to APMC caused SMI 4 Access to one of the Local Traps caused SMI 3 One of the local Standby timers caused SMI 2 Global Standby Timer caused SMI 1 SRBTN# or BATLOW# caused SMI 0 reserved
See Also: #01168 - #01200 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Suspend/Resume Control 1 register: Bit(s) Description (Table 01202) 7 BATLOW# bypasses Suspend delay timer and activates SMI# immediately 6 IRQ8 will NOT cause a resume 5 COM RI (Ring) will NOT cause a resume ("Wake on Ring" function) 4 BATLOW# will not prevent a resume 3 is set by power management software at the end of a suspend routine 2 can be set by power management software at the end of a suspend routine 1-0 Set suspend mode. 00 Suspend Disabled. 01 reserved. 10 Suspend-to-DRAM. 11 Suspend-to-Disk
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Suspend/Resume Control 2 register: Bit(s) Description (Table 01203) 7-1 reserved 0 EXTSMI# will NOT cause a resume event
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX SMOUT Control register: Bit(s) Description (Table 01204) 7-6 reserved 5-0 Writing to any bits sets the state of the 6 SMOUTx pins.. SMOUT5 is not effected if it is configured for DOE# function. SMOUT4 is not effected if it is configured for RTCALE function
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Clock Control register: Bit(s) Description (Table 01205) 7 Clock Throttle standy by timer frequency. =1 32ms. =0 4ms
Note: Sets the granularity of the Clock Throttle Standby Timer 6-5 reserved 4 Enable Auto Clock Throttle 3-2 STPCLK# Mode. 00 Disable STPCLK# Function. 01 Enable stop grant mode. 10 Enable stop clock mode. 11 reserved 1 Enable clock throttling 0 Enable "PCI Clock can be stopped"
See Also: #01168 - PORT xxxxh"Intel 82371"
(Table 01206) Values for Intel 82371MX Shadow Register Value AT Port Description 00h 00h Channel 0 Base Address Register (low byte) 01h 00h Channel 0 Base Address Register (high byte) 02h 01h Channel 0 Base Word Count Register (low byte) 03h 01h Channel 0 Base Word Count Register (high byte) 04h 02h Channel 1 Base Address Register (low byte) 05h 02h Channel 1 Base Address Register (high byte) 06h 03h Channel 1 Base Word Count Register (low byte) 07h 03h Channel 1 Base Word Count Register (high byte) 08h 04h Channel 2 Base Address Register (low byte) 09h 04h Channel 2 Base Address Register (high byte) 0Ah 05h Channel 2 Base Word Count Register (low byte) 0Bh 05h Channel 2 Base Word Count Register (high byte) 0Ch 06h Channel 3 Base Address Register (low byte) 0Dh 06h Channel 3 Base Address Register (high byte) 0Eh 07h Channel 3 Base Word Count Register (low byte) 0Fh 07h Channel 3 Base Word Count Register (high byte) 10h 08h DMA1 Command Register 11h 0Bh Channel 0 Mode Register 12h 0Bh Channel 1 Mode Register 13h 0Bh Channel 2 Mode Register 14h 0Bh Channel 3 Mode Register 15h 0Fh DMA1 Mask Register 16h C4h Channel 5 Base Address Register (low byte) 17h C4h Channel 5 Base Address Register (high byte) 18h C6h Channel 5 Base Word Count Register (low byte) 19h C6h Channel 5 Base Word Count Register (high byte) 1Ah C8h Channel 6 Base Address Register (low byte) 1Bh C8h Channel 6 Base Address Register (high byte) 1Ch CAh Channel 6 Base Word Count Register (low byte) 1Dh CAh Channel 6 Base Word Count Register (high byte) 1Eh CCh Channel 7 Base Address Register (low byte) 1Fh CCh Channel 7 Base Address Register (high byte) 20h CDh Channel 7 Base Word Count Register (low byte) 21h CDh Channel 7 Base Word Count Register (high byte) 22h D0h DMA2 Command Register 23h D6h Channel 5 Mode Register 24h D6h Channel 6 Mode Register 25h D6h Channel 7 Mode Register 26h DEh DMA2 Mask Register 27h 20h PIC1 ICW1 28h 21h PIC1 ICW2 29h 21h PIC1 ICW3 2Ah 21h PIC1 ICW4 2Bh 20h PIC1 OCW2 2Ch A0h PIC2 ICW1 2Dh A1h PIC2 ICW2 2Eh A1h PIC2 ICW3 2Fh A1h PIC2 ICW4 30h A0h PIC2 OCW2 31h 70h NMI mask / RTC address 32h 03FAh COM1 FIFO Enable Register (only bits 0,3,6 & 7 valid) 33h 02FAh COM2 FIFO Enable Register (only bits 0,3,6 & 7 valid) 34h 03EAh COM3 FIFO Enable Register (only bits 0,3,6 & 7 valid) 35h 02EAh COM4 FIFO Enable Register (only bits 0,3,6 & 7 valid) 36h 40h TIMER 0 Count Register (low byte) 37h 40h TIMER 0 Count Register (high byte) 38h 20h Master PIC OCW3 Register (bits 0,2 & 5 only valid) 39h A0h Slave PIC OCW3 Register (bits 0,2 & 5 only valid)
Desc: This register is used to read the current programmed value of certain AT compatable I/O ports which are traditionally write-only.
Note: To read a given register, write the value from the table to the shadow register, then immediately re-read the shadow register. The returned value is the current value of the I/O port.
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Burst Clock/Clock Throttle Break Enable 0 register: Bit(s) Description (Table 01207) 7 Enable IRQ7 6 Enable IRQ6 5 Enable IRQ7 4 Enable IRQ4 3 Enable IRQ3 2 reserved 1 Enable IRQ1 0 Enable IRQ0
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Event Enable 1 register: Bit(s) Description (Table 01208) 7 Enable IRQ15 6 Enable IRQ14 5 reserved 4 Enable IRQ12 3 Enable IRQ11 2 Enable IRQ10 1 Enable IRQ9 0 Enable IRQ8
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Event Enable 2 register: Bit(s) Description (Table 01209) 7 (Clock Throttle Break Event,Burst Clock Event) reserved. (System Event,Stop Break Event,Clock Throttle Break Event) Enable BATLOW# & SRBTN# 6 Enable EXTSMI# 5 Enable SMI# 4 (System Event,Stop Break Event,Clock Throttle Break Event) Enable NMI. (Burst Clock Event) reserved 3 (System Event,Stop Break Event,Clock Throttle Break Event) Enable INTR. (Burst Clock Event) reserved 2 reserved 1 Enable COMRI# 0 Enable events of selected type
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Event Enable 3 register: Bit(s) Description (Table 01210) 7-2 reserved 1 Enable EXTEVNT# 0 Enable PHLDA#
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Event Enable 4 register: Bit(s) Description (Table 01211) 7 Enable PMAC1 6 Enable PMAC0 5 Enable PAC5 4 Enable PAC4 3 Enable PAC3 2 Enable PAC2 1 Enable PAC1 0 Enable PCSC
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Event Enable 5 register: Bit(s) Description (Table 01212) 7 Enable COM4 6 Enable COM3 5 Enable COM3 4 Enable COM1 3 Enable Secondary FDC 2 Enable Primary FDC 1 Enable Secondary IDE 0 Enable Promary IDE
See Also: #01168 - PORT xxxxh"Intel 82371"
Bitfields for Intel 82371MX Event Enable 6 register: Bit(s) Description (Table 01213) 7 Enable Audio-E 6 Enable Audio-D 5 Enable Audio-C 4 Enable Audio-B 3 Enable Audio-A 2 Enable Parallel 3 1 Enable Parallel 2 0 Enable Parallel 1
See Also: #01168 - PORT xxxxh"Intel 82371"
Format of PCI Configuration for Intel 82371FB/82371SB Function 1 (IDE): Offset Size Description (Table 01214) 00h 64 BYTEs header (see #00878) (vender ID 8086h, device ID 1230h/7010h) 20h DWORD Bus Master Interface Base Address (see PORT xxxxh"Intel 82371SB") 40h WORD IDE timing modes, primary channel (see #01223) 42h WORD IDE timing modes, secondary channel (see #01223) 44h BYTE (82371SB) slave IDE timing register (see #01224) 45h 187 BYTEs reserved
See Also: #01167 - #01215 - PORT xxxxh"Intel 82371SB"
Format of PCI Configuration data for Intel 82371SB Function 2 (USB): Offset Size Description (Table 01215) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 7020h) 20h DWORD I/O space base address (see PORT xxxxh"Intel 82371SB") 40h 32 BYTEs reserved 60h BYTE Serial Bus Specification release number 00h pre-release 1.0 10h Release 1.0 61h 9 BYTEs reserved 6Ah WORD miscellaneous status (see #01225) 6Ch 84 BYTEs reserved C0h WORD legacy support (see #01226) C2h 62 BYTEs reserved
See Also: #01167 - #01214 - PORT xxxxh"Intel 82371SB"
Bitfields for Intel 82371FB/82371SB top of memory register: Bit(s) Description (Table 01216) 7-4 top of ISA memory (in megabytes, less 1; i.e. 0001 = 2M) 3 ISA/DMA lower BIOS forwarding enable 2 (82371SB) enable A000/B000 segment forwarding to PCI bus 1 enable forwarding ISA/DMA 512K-640K region to PCI bus 0 reserved
See Also: #01167 - #01217
Bitfields for Intel 82371FB/82371SB miscellaneous status register: Bit(s) Description (Table 01217) 15 (82371SB) enable SERR# on delayed transaction. Write 1 to clear this bit 14-8 reserved 7 (82371SB) NB Retry Enable 6 (82371SB) EXTSMI# Mode Enable. Allow special SERR# protocol between PCI bridge and 82371 5 reserved 4 (82371SB) enable USB. Disable USB's master enable and I/O decode enable prior to clearing this bit! 3 reserved 2 (82371FB) PCI Header Type Bit enable. =1 report multifunction device in PCI configuration header 1 (82371FB) internal ISA DMA/external DMA Mode status (read-only). =0 normal DMA operation 0 (82371FB) ISA Clock Divisor status (read-only). (82371SB) ISA Clock Divisor (read-write). =1 SYSCLK clock divisor is 3. =0 SYSCLK clock divisor is 4
See Also: #01167 - #01216
Bitfields for Intel 82371FB/82371SB/82371MX motherboard IRQ Route Control: Bit(s) Description (Table 01218) 7 disable IRQ routing 6 enable MIRQx/IRQx sharing 5 (82371SB only) enable IRQ0 output 4 reserved (0) 3-0 ISA IRQ number to which to route the PCI IRQ
Notes: IRQs 0-2, 8, and 13 are reserved. Interrupt sharing should only be enabled when the device connected to the MIRQ line and the device connected to the IRQ line both produce active high, level triggered interrupts.
See Also: #01167 - #01168 - #01216 - #01219
Bitfields for Intel 82371FB/82371SB/82371MX motherboard DMA control: Bit(s) Description (Table 01219) 7 type F DMA buffer enable 6-4 reserved 3 (82371FB only) disable motherboadr DMA channel. (SB/MX) reserved (0) 2-0 DMA channel number (100 = disabled [default]). (82371FB) Type F and Motherboard DMA. (82371SB/MX) Type F DMA
See Also: #01167 - #01168 - #01218
Bitfields for Intel 82371FB/83271SB programmable chip select control register: Bit(s) Description (Table 01220) 15-2 I/O address which will assert PCS# signal 1-0 PCS address mask. 00 four bytes. 01 eight contiguous bytes. 10 disabled. 11 sixteen contiguous bytes
See Also: #01167 - #01219 - #01221
Bitfields for Intel 82371SB Deterministic Latency Control register: Bit(s) Description (Table 01221) 7-4 reserved 3 enable SERR# on delayed transaction timeout 2 enable USB passive release 1 enable passive release 0 enable delayed transactions
See Also: #01167 - #01220
Bitfields for Intel 82371FB/82371SB SMI Control Register: Bit(s) Description (Table 01222) 7-5 reserved 4-3 Fast-Off Timer freeze/granularity selection. 00 one minute granularity (assuming 33 MHz PCICLK). 01 disabled (frozen). 10 one PCICLK. 11 one millisecond 2 STPCLK# scaling enable. =1 enable Clock Scale bytes in PCI configuration space 1 STPCLK# signal enable. =1 assert STPCLK# on read from PORT 00B2h 0 SMI# Gate. =1 enable SMI# on system management interrupt
Notes: Bit 1 is cleared either with an explicit write of 0 here, or by any write to PORT 00B2h. Bit 0 does not affect the recording of SMI events, so a pending SMI will cause an immediate SMI# when the bit is set
See Also: #01167 - #01079
Bitfields for Intel 82371FB/82371SB/82371MX IDE timing modes: Bit(s) Description (Table 01223) 15 IDE decode enable 14 (82371SB) slave IDE timing register enable (see #01224). (82371MX) primary/secondary address decode (=0 primary, =1 secondary) 13-12 IORDY# sample point. 00 five clocks after DIOx# assertion. 01 four clocks. 10 three clocks. 11 two clocks 11-10 reserved 9-8 recovery time between IORDY# sample point and DIOx#. 00 four clocks. 01 three clocks. 10 two clocks. 11 one clock 7 (FB/SB) DMA timing enable only, drive 1. (MX) reserved 6 prefetch and posting enable, drive 1 5 IORDY# sample point enable drive select 1 4 fast timing bank drive select 1 3 (FB/SB) DMA timing enable only, drive 0. (MX) reserved 2 prefetch and posting enable, drive 0 1 IORDY# sample point enable drive select 0 0 fast timing bank drive select 0
See Also: #01214 - #01168
Bitfields for Intel 82371SB slave IDE timing register: Bit(s) Description (Table 01224) 7-6 secondary drive 1 IORDY# sample point. 00 five clocks after DIOx# assertion. 01 four clocks. 10 three clocks. 11 two clocks 5-4 secondary drive 1 recovery time. 00 four clocks. 01 three clocks. 10 two clocks. 11 one clock 3-2 primary drive 1 IORDY# sample point 1-0 primary drive 1 recovery time
See Also: #01223
Bitfields for Intel 82371SB miscellaneous status: Bit(s) Description (Table 01225) 15-1 reserved 0 USB clock selection. =1 48 MHz. =0 24 MHz
See Also: #01215 - #01226
Bitfields for Intel 82371SB legacy support register: Bit(s) Description (Table 01226) 15 A20GATE pass-through sequence ended. Write 1 to clear this bit 14 reserved 13 USB PIRQ enabled 12 USR IRQ status (read-only) 11 trap caused by write to PORT 0064h. Write 1 to clear this bit 10 trap caused by read from PORT 0064h. Write 1 to clear this bit 9 trap caused by write to PORT 0060h. Write 1 to clear this bit 8 trap caused by read from PORT 0060h. Write 1 to clear this bit 7 enable SMI at end of A20GATE Pass-Through 6 A20GATE pass-through sequence in progress (read-only) 5 enable A20GATE pass-through sequence. (write PORT 64h,D1h; write 60h,xxh; read 64h; write 64h,FFh) 4 enable trap/SMI on USB IRQ 3 enable trap/SMI on PORT 0064h write 2 enable trap/SMI on PORT 0064h read 1 enable trap/SMI on PORT 0060h write 0 enable trap/SMI on PORT 0060h read
See Also: #01215 - #01225
Format of PCI Configuration Data for Intel 82557: Offset Size Description (Table 01227) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 1229h) (see #00873) 10h DWORD base address of memory-mapped Control/Status Registers (4K) (see #01228) 14h DWORD base address of I/O-mapped Control/Status Registers (32 ports) 18h DWORD base address of Flash memory (1M) 40h 192 BYTEs unused
See Also: #01098
Format of Intel 82557 Control/Status Registers: Offset Size Description (Table 01228) 00h WORD SCB status word 02h WORD SCB command word 04h DWORD SCB general pointer 08h DWORD PORT 0Ch WORD Flash control register 0Eh WORD EEPROM control register 10h DWORD MDI control register 14h DWORD Early RCV Interrupt Rx byte count (RXBC) register
Note: See www.intel.com/design/network/datashts/64434604.pdf for additional details
See Also: #01228
Format of PCI Configuration Data for Intel 82441FX: Offset Size Description (Table 01229) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 1237h) (see #00873) 40h 16 BYTEs reserved 50h WORD PMC Configuration (see #01230) 52h BYTE deturbo counter control when deturbo mode is selected (see PORT 0CF9h), the chipset places a hold on the memory bus for a fraction of the time inversely proportional to the value in this register (i.e. C0h = 1/4, 80h = 1/2, 40h = 3/4, 20h = 7/8, etc.) 53h BYTE DBX buffer control (see #01231) 54h BYTE auxiliary control (see #01232) 55h WORD DRAM Row Type (see #01233) 57h BYTE DRAM Control (see #01234) 58h BYTE DRAM Timing (see #01235) 59h 7 BYTEs Programmable Attribute Map registers 0-6 (see #01118) 60h 8 BYTEs DRAM Row Buondary registers 0-7 each register N indicates cumulative amount of memory in rows 0-N (each 64 bits wide), in 8M units 68h BYTE Fixed DRAM Hole Control 69h 7 BYTEs reserved 70h BYTE Multi-Transaction Timer number of PCLKs guaranteed to the current agent before the 82441 will grant the bus to another PCI agent on request 71h BYTE CPU Latency Timer (see #01236) 72h BYTE System Management RAM control (see #01123) 73h 29 BYTEs reserved 90h BYTE Error Command (see #01237) 91h BYTE Error Status (see #01238) 92h BYTE reserved 93h BYTE Turbo Reset Control (see #01239) 94h 108 BYTEs reserved
See Also: #01098 - #01108
Bitfields for Intel 82441FX PMC Configuration Register: Bit(s) Description (Table 01230) 15 WSC Protocol Enable 14 Row Select/Extra Copy select (read-only). =1 pins on PMC configured as two additional row selects (6/7). =0 extra copy of two lowest memory address bits enabled 13-10 reserved 9-8 host frequence select. 00 reserved. 01 60 MHz. 10 66 MHz. 11 reserved 7 reserved 6 ECC/Parity TEST enable 5-4 DRAM Data Integrity Mode. 00 no parity/ECC. 01 parity generated and checked. 10 ECC generated and checked, correction disabled. 10 ECC generated and checked, correction enabled 3 reserved 2 In-Order Queue size (0=one, 1=four) 1-0 reserved
See Also: #01229 - #01231
Bitfields for Intel 82441FX DBX buffer control register: Bit(s) Description (Table 01231) 7 enable delayed transactions 6 enable CPU-to-PCI IDE posting 5 enable USWC Write Post during I/O Bridge access 4 disable PCI Delayed Transaction timer 3 enable CPU-to-PCI Write Post 2 enable PCI-to-DRAM pipeline 1 enable PCI Burst Write Combining 0 enable Read-Around-Write
See Also: #01229 - #01230
Bitfields for Intel 82441FX auxiliary control register: Bit(s) Description (Table 01232) 7 enable RAS precharge 6-2 reserved 1 Lower Memory Address Buffer Set A. =0 8mA. =1 12mA 0 reserved
See Also: #01229
Bitfields for Intel 82441FX DRAM Row Type register: Bit(s) Description (Table 01233) 15-14 row 7 DRAM type 13-12 row 6 DRAM type 11-10 row 5 DRAM type 9-8 row 4 DRAM type 7-6 row 3 DRAM type 5-4 row 2 DRAM type 3-2 row 1 DRAM type 1-0 row 0 DRAM type. 00 fast page-mode DRAM. 01 EDO DRAM. 10 BEDO DRAM. 11 empty row
See Also: #01229 - #01234
Bitfields for Intel 82441FX DRAM Control register: Bit(s) Description (Table 01234) 7 reserved 6 enable DRAM Refresh Queue 5 enable DRAM EDO Auto-Detect Mode 4 DRAM Refresh Type. =0 CAS before RAS. =1 RAS only 3 reserved 2-0 DRAM refresh rate. 000 disabled. 001 normal (as set by PMCCFG register). 01x reserved. 1xx reserved. 111 fast refresh (every 32 host clocks)
See Also: #01229 - #01233 - #01235
Bitfields for Intel 82441FX DRAM Timing register: Bit(s) Description (Table 01235) 7 reserved 6 enable WCBR Mode 5-4 DRAM Read Burst Timing BEDO EDO FPM. 00 x333 x444 x444. 01 x222 x333 x444. 10 x222 x222 x333. 11 res. res. res. 3-2 DRAM Write Burst Timing (B)EDO FPM. 00 x444 x444. 01 x333 x444. 10 x333 x333. 11 x222 x333 1 RAS-to-CAS delay. =1 one clock. =0 zero clocks 0 insert one MA Wait State
See Also: #01229 - #01234
Bitfields for Intel 82441FX CPU Latency Timer register: Bit(s) Description (Table 01236) 7-5 reserved 4-0 snoop stall count value
See Also: #01229
Bitfields for Intel 82441FX Error Command register: Bit(s) Description (Table 01237) 7-5 reserved 4 enable SERR# on receiving Target Abort 3 enable SERR# on PCI Parity Error (PERR#) 2 reserved 1 enable SERR# on receiving multiple-bit ECC/Parity error 0 enable SERR# on receiving single-bit ECC error
See Also: #01229 - #01238
Bitfields for Intel 82441FX Error Status register: Bit(s) Description (Table 01238) 7-5 DRAM row causing first multi-bit error (read-only) 4 multiple-bit uncorrectable error detected. Write 1 to this bit to clear it 3-1 DRAM row causing first single-bit error (read-only) 0 single-bit correctable ECC error detected. Write 1 to this bit to clear it
See Also: #01229 - #01237
Bitfields for Intel 82441FX,82443EX/LX Turbo Reset Control register: Bit(s) Description (Table 01239) 7-4 reserved 3 enable BIST on hard reset 2 reset CPU 1 reset mode (0 = soft reset, 1 = hard reset) 0 deturbo mode (82441FX). Reserved (82443EX/LX)
Note: BIST should not be enabled during a soft reset
See Also: #01229 - #01129 - PORT 0CF9h
Format of PCI Configuration data for Intel 82454KX/GX: Offset Size Description (Table 01240) 00h 64 BYTEs header (see #00878) (vendor ID 8086h, device ID 84C4h) !!!intel\29052301.pdf pg. 40 40h DWORD top of system memory 44h 4 BYTEs reserved 48h BYTE PCI decode mode 49h BYTE bridge device number 4Ah BYTE PCI bus number 4Bh BYTE PCI subordinate bus number 4Ch BYTE PB configuration 4Dh 4 BYTEs reserved 51h BYTE deturbo counter control 52h BYTE reserved 53h BYTE CPU read/write control 54h WORD PCI read/write control 56h BYTE reserved 57h BYTE SMM Enable 58h BYTE video buffer area enable 59h 7 BYTEs Programmable Attribute Map registers 0-6 (see #01118) 60h 16 BYTEs reserved 70h BYTE Error Command 71h BYTE Error Status 72h 6 BYTEs reserved 78h WORD memory gap range 7Ah WORD memory gap upper address 7Ch DWORD PCI frame buffer 80h 8 BYTEs reserved 88h DWORD high memory gap start address 8Ch DWORD high memory gap end address 90h 8 BYTEs reserved 98h DWORD (GX only) I/O Space Range #1 9Ch BYTE PCI reset 9Dh 3 BYTEs reserved A0h DWORD (GX only) I/O Space Range #2 A4h DWORD I/O APIC range A8h 8 BYTEs reserved B0h WORD configuration values driven on reset B2h 2 BYTEs reserved B4h WORD captured system configuration values (read-only) B6h 2 BYTEs reserved B8h DWORD SMM range BCh BYTE high BIOS register BDh 3 BYTEs reserved C0h DWORD PB Extended Error Reporting Command C4h DWORD PB Extended Error Reporting Status C8h DWORD PB Retry Timers CCh 52 BYTEs reserved
See Also: #00878
Category: Expansion Bus Bios - Int 1Ah - P
|
| Interrups | Categories | Contents |